Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hi,
It seems to be a bug in hal_device_reset() when using S132.
On line 8 above the function sd_power_gpregret_set() is called with the wrong arguments. The first arguments...
can I use an nRF52840 based BLE gateway? Backhaul would be either 10/100 Ethernet (via Wiznet or Microchip controller chip) or a cellular module. Is the clock speed sufficient...
I am unable to get 6 notifications per connection event. I am connecting two nrf32832's, one as a central, one as a peripheral. To make this as simple as possible, I limited...
Hi
We are able to provision several mesh-servers.
The log on the RTT-Viewer of the client looks normal:
0> <t: 915394>, mesh.c, 178, Local provisioning link established...
I am working with the peripheral/flash_fds in SDK14. I need to adapt it to use RTT instead of uart
I have made the obvious changes to switch from uart to RTT, eg substituting...
Hi everybody,
I'm trying to use the example ble_app_hrs with s110 on the PCA10001 Board and the ble_app_hrs_c with s120 also on an other PCA10001.
I changed some led flag...
I have already explored how to fix the related problem in the DevZone. I think the firmware of the ATSAM3U2CA-AU is erased. Here, I have two problems:
1, How can I get the...
Hi,
According to the code in PCA10059.h:
#define RX_PIN_NUMBER 11 #define TX_PIN_NUMBER 9
I would like to know what pins are related to number 9 and 11 in this schematic...
Hello,everyone.
If you have some suggestions,and you leave them, I would appreciate it very much.
I designed a pcb base on nRF51822. It can only be searched by mobile...
Dear Nordic support,
I am working on a device based on the FreeRTOS heart rate example and I am having difficulties with the BLE connection when connecting to iPhone X...
Hi, I want to reduce current my module.
I used SDK15.0.0ver, nRF52832
I have 2 questions.
1. I used app_uart_close();
But My module was reset again.
2. I want to...
hi...
i want to check my data for every minute , so i set the timer for one minute.
but its not working ....... how to do?
i have set the timer like below
i am finding...
Hello nordic team, I have a question regarding BLE Mesh and Uart0:
The InfoCenter is saying that Uart0 is blocked when using the serial Support. I don't wan't to use the...
