Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
Hi all,
The setup that I am aiming for has a number of nodes, which will send the IMU data to a central base station. The communication is achieved using a bunch of nRF24L01...
I keep getting stuck in the TIMER1_IRQHandler function.
When I debug the code, I get to line 20 (exiting interrupt function scope) and then the assembly code hits a nop...
Hello!
I have developed a BLE HID (HOGP) device in Nordic SDK 15.0.0 starting from an example project: ble_app_hids_keyboard .
The HID device that I have developed however...
We have a setup where we want to measure the current consumption of a battery-powered device:
The batteries are soldered to the device, and cannot be removed.
We can...
Dear Team,
i hope you are doing good,
I am working on nrf51822 controller, using SDK is 12.3.0 on windows environment. Soft-device is s130
i am planning interface...
Hi,
Wanted to interface NRF52840-DK to Board Mount Basic Pressure Sensors (Honeywell) ABPDANT005PGAA5 which is of anlog output type.Can u suggest can i go ahead with the...
hi......
my peripheral device is heating up quickly what is the way to reduce or avoid heating of the device ?
when i put my device in sleep mode more than the wake up...
Using SDK_14 and unmodified SAADC example on pca10040.
Initially connected A0 (PO.03) to ground but getting seemingly random values.
<info> app: ADC event number: 586...
The file components/libraries/timer/app_timer_freertos.c does not have the function app_timer_cnt_get() defined. Compiling libraries that require it (like external/lwip/src...
I used nRF5_SDK_15.2.0_9412b96\nRF5_SDK_15.2.0_9412b96\examples\peripheral\spis to test spi,but only the first time can receive data. logs like below,"1234567"
is I send...
static void onoff_state_value_update(app_onoff_server_t * p_server) { /* Requirement: If delay and transition time is zero, current state changes to the target state. */ if...
My app (using S130v2.0.1 nRF51822 SDK12.3) triggers app_error_fault_handler (seen on a PIN; since not able to debug due to timing) on sd_softdevice_disable(). A snippet of...
Hi,
I am using nRF5_SDK_12.3.0 and based on \ble_peripheral\ble_app_uart ( with softdevice of s130) to build my application.
Recently, I tried to add the wdt to my nrf51822...
I adapted the light switch demo of the nRF5 SDK for Mesh for sending a series of reliable on/off messages sequentially from an nRF52840 Preview DK to 20 Thingy:52 servers...
Hi. I have set up a nine node mesh using Thread and the nRF52840 chips. I am using the COAP example. All my nodes are visible and i am able to send pings between them. I am...
