Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
hi, nordicer:
two device, a peripheral and a apple phone as central. we want to support scan request and response with ADV_IND mode, I understand as following:
(1) peripheral...
Hello,
I use the LAIRD module BL652 with the nRF52832.
My project consist of do a synchronous between many board. Each second, I restart a timer of 1 second.
I include...
Hi guys!
I want to add SPI to my BLE project to read some data from my gyro.
Adding other headers was no problem, but when I want to add some code from the SPI-Example I...
Hello,
I am trying to run mesh DFU examples in following environment:
Distributor ID: Ubuntu Description: Ubuntu 18.04 LTS Release: 18.04 Codename: bionic
I have installed...
I am in the process of porting a current production application from SDK 13.0.0 to SDK 14.2.0 https://devzone.nordicsemi.com/f/nordic-q-a/39494/dfu-migration-sdk-13-0-0-s132...
Hi!
I used nRF Connect Programmer (desktop version) for writing firmware connectivity_1.2.3_115k2_with_s132_3.1.hex. And nRF52840 dongle doesn't display in the device list...
Hi everyone,
Yesterday I asked a question, but no one has answered yet.
Previous question:
https://devzone.nordicsemi.com/f/nordic-q-a/35067/nfc-tag-can-t-work-with...
Following file: nRF5_SDK_15.2.0_9412b96/modules/nrfx/drivers/src/nrfx_saadc.c
I've now just add gcc specific unused attributes.
This is just a work around. Best would...
Hi!
I am planning to move sample code of uart.because I port the function of uart to spi sample code.
now i take the SDK14.0.0 and uart sample(examples/peripheral/uart...
Hi, I can make a DFU over BLE with nRF connect 2.5.0 Bluetooth Low Energy, all is OK. I use my nRF52840-Dongle PCA10059 (Serial port: COM19 | USB: Nordic Semiconductor nRF52...
Hello,
I'm using SPI 3 to communicate with a NAND memory. I'm able to go up to 8MHz but not more than that. Do I need to set an array list or use the spi manager.
Is there...
Hi Nordic Support, community,
Recently I started working with the nRF52 dongle, after flashing a hex file via nRFConnect/Programmer applic (version 2.5.running on Windows...
Can anyone tell me where the board / device choices in Eclipse come from, as shown in the screen shot below? I have none.
I copied my Eclipse installation from a working...
Hi all I've already setup my Eclipse environment as described in Development with GCC and Eclipse . Now I want to use the SPI libraries for my example. But I got the first...
Hi
The compiling of standard TWI sensor example is giving me an error with SES.
Please find attached a snapshot of the issue.
Need your help ASAP. Thanks
Ch...
