Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
Hello,
I am a beginner with Nordic semiconductor. I downloaded SDK v15.0.0 and used some of the examples and it worked perfectly for me.
My project uses different modules...
Wiring diagram
Testing process，The product will automatically disconnect. But it can connect again.
After setting the voltage to 1.8V in the voltage Reguator,...
This time I am trying to run Wireless UART Example but it seems that it does not work.
After I flashed dev board no LED were turned ON or flashing but web site says:
LED...
Hi!
Is there an example to extend the Bluetooth MTU size to more than 20 bytes together with SDK 15.2?
I found only examples with older versions.
Thank you in advance...
Hello
I'm wondering if it is possible to upgrade over-the-air from SDK11 to SDK15.
I know already that using the example bootloader from SDK11 will not work because the...
Setup: nRF5_SDK_15.2.0_9412b96 / s132_nrf52_6.1.0_softdevice / nrf52832
I tried to make a multilink nus central (PCA10040) with 2 peripherals (PCA10028) connected to it...
Hi, I would like to send data from nRF52840 Dongle to Raspberry Pi 3 through USB-UART. I programmed the ble_app_uart_c example found in SDK 15.2 and I connected that to my...
NRF51822 RM 3.0 section 14.1 states each GPIO pin has DETECT, but where is the register to read per-pin detect? From the manual: "Each pin has a separate DETECT signal, and...
Hi,
Now, i want to use SAADC with softdevice of SDK15.0 to make a beacon program.
I migrate SAADC example in nRF5_SDK_15.0.0_a53641a\examples\peripheral to beacon with...
Hi,
I am using nrf_sniffer_2.0.0-beta-2_10Sep2018_3ef662e for capturing ble mesh packets but i am finding LE LL packets of my node with mesh beacons in my wireshark. Even...
Hello, I am new to nordic sdk and tools. I am planning to develop a nRF52840 DK based sensor device that reads I2C temperature sensor data ad broadcast it periodically. Also...
Hi,
I'm testing the BLE_UART example : <InstallFolder>\examples\peripheral\ble_app_uart . For this, I use the nRF52840 with SDK 15.2 and s140 softdevice.
I would like...
So I am using nrf52832 and making a whole new app in ios. My objective of the app is to get the sensor data (specially motion sensor data and accelerometer data) which is...
Hi,
I am trying to add app_uart into the heart rate sensor example. I called uart_config(); in the function function, but when I open the serial monitor, The errors shown...
