nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
hi, this is Shivaji, I have to work on Bluetooth mesh, so which kit I have to buy, can I buy thingy52 or can I buy nrf52dk. which board should I buy, and can get the android...
Dear Sir,
I have bought a BMD 300 chip.
I have implemented a firmware with segger embedded studio and SDK15 for nrf52832.
I have flashed it to BMD300 DK from Rigado...
Hi:
As we are going to use nRF52840 on our product, we were trying the check the HW security implemented in the chip. nRf52840 implemented Arm TrustZone CryptoCell-310 in...
Hi Team,
I hope you are doing good.....
I am using nRF51822 with the SDK version 12.3.0 in windows, keil version is 5.26.
In the blu_app_uart Application i want...
Hi,
In order to isolate the issue, I've created an app that :
1. switches to dc2dc mode.
2. calls sd_app_evt_wait()
I still see 3ma consumption,
any ideas...
Hi
Actually i have a big project and have a problem in the estimation of FLASH and RAM memory for the project
i ma going to implement the mesh SDK with the BLE Stack because...
Hello,
I am working with a custom board with the nrf52832 chip.
I have merged and written the following on the board: SD (s132, 6.1.0) + secure bootloader from the latest...
Hello,
I purchased a nRF52 DK board and sparkfun nrf52832 breakout board , and was successful with blinking the LED on the breakout board.
In order to test if I would...
Hello,
(I am using SDK 15.1 on a linux system)
I will breakdown the question in two parts -
when do we get fatal ? - i know one or two cases for example when softdevice...
Hi.....
i want to transfer the data for every one minute from peripheral device to nrf connect via (phone app).. how to declare in the program and what function to be used...
Dear all,
When I added more than 4 buttons by modifying the example "ble_app_uart" of nRF5_SDK_15.2.0_9412b96, nRF52832 can not run normally.
Another strangely problem...
Hi,
Just got four 52840 USB dongles, with the intent to evaluate the Nordic BT Mesh. But I've been unable to get even a simple Blinky example programmed on the dongle. I...
Hi all, I've just implemented light switch proxy example and it's working very well. Now, I have three NRF52832 boards, and for instance, I have:
A board in the garden...
