I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hello everyone,
I have 2 chip; Bluegiga and nRF51-DK
I can easily advertise my custom service in Bluegiga chip. As you can see, nRF Connect application shows my service...
I think one way or the other the struct ble_gatts_evt_t must be correlated with the GATT profile, that is, ble_gatts_evt_t should have services and characteristics as its...
Hi,
> Context:
I run a baremetal application that I would like to enhance with bluetooth.
I am considering a BLE module from NS.
I currently have a SoC (nanopi...
I have created a nRF52 based peripheral device which is used to stream sensor data to a connected central device, usually an iPhone. I can stream data, reliably to the iPhone...
I have an odd situation. I've been using an iPhone 5 and 6 to connect to, and test against, both an nRF51 (redbear nano) and the same code built for nRF52. It works fine....
Hi All,
i am using nrf51822 with SDK 12 and i am not able to find where All BAUDRATE Macro is defined for APP_UART.
so anyone can tell about that in which file it is...
I looked at examples and added identical code to my own app, specifically to a) set the gatt_enable_params.att_mtu to GATT_MTU_SIZE_DEFAULT, and b) to handle BLE_GATTS_EVT_EXCHANGE_MTU_REQUEST...
Hi,
Is there an extensive documentation about programming process of a nrf52832 using keil?
I just spent hours figuring out that I had to use Softdevice erase flash algorithm...
I just followed "Testing the example manually (without bonding)" steps to manually update firmware by Master Control Panel.
But every time, I got log message, "SERVER:...
I am implementing mqtt client on Nrf52832 with the example provided in the IoT SDK. I am looking for the correct way to make the client to run with Non-Nordic socket stack...
I've just finished my first layout for nRF51822, and I need a help with the attenna design.
The RF part of the schematic and layout is a copy of your reference design, "PCA10004...
Hi
I'm using BLE400 board (from waveshare) which have a nrf51822 chip on it. When I want to program the softdevice with nrfgo I encounter the following error:
link text...
Hi, I got a problem.
I created a timer, interval is 30ms.
#define MIN_CONN_INTERVAL MSEC_TO_UNITS(150, UNIT_10_MS) /**< Minimum acceptable connection interval (0.02...
