Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi,
I'm trying to use sd_ble_gattc_characteristics_discover to figure out which characteristics are in a service.
On the whole it seems pretty obvious (keep calling...
I'm using the nRF52 + SDK11.0.0 + s132 and the ble_hrs example. The function conn_params_init() is called to initialize the connection parameters that the peripheral will...
Is there a way to pause all peripherals when hitting a breakpoint? In particular, I would like to freeze the RTCs when I hit a breakpoint. My app wakes up once a second, and...
I`m trying to operate PWM and soft device at the same time.
I have to make 4 Mhz using PWM block so I checked the PWM driver. There is no problem when using peripheral/pwmdriver...
Hello there.
I´m using a Taiyo Yuden evaluation board with a nRF51422 to connect with 3 different sensors. In addition to that there are also 2 buttons connected to the...
I am working on a BLE peripheral. I have a large, variable length characteristic I need to set from the central.
When the central is the BTool, I can write up to the maximum...
I'm using the nRF52 + SDK11.0.0 + s132. I started with the ble_hrs example and modified it. I now want to make the service/characteristics use proprietary UUIDs and I'm following...
I have been having issues with bootloader launching my application on a custom nRF52832 based hardware device.
The bootloader itself seems to be successfully completing...
When designing the layout for my circuit using nRF52832 I've noticed that the values of CL connected to the ANT pin changed from L= 3.9nH and C=0.8pF to L=3.3nH and C=1pF...
Hello, I'm trying to generate DFU keys with the nrfutil.exe tool from Master Control Panel 3.10.0.
I always get errors....
C:\Program Files (x86)\Nordic Semiconductor...
Hi,
nrf51822 device obverse six bytes mac addres could change，when OTA failed.
six bytes mac address, five bytes fixed, one byte can change when OTA failed.
Now，my app...
Hello,
I am using Nordic Nur-10W develop kit, trying to compile NurApiExample in Raspberry Pi. I wrote a Makefile, and complie process was OK. However, undefined reference...
hi
im using sdk v6 and when i turn my board on it goes to bootloader and i can upload my program into it .
the problem is that i want it to run to my main program after...
Hello,
I would like to use a custom flash memory layout for the flash memory of nrf52:
I thought that I should be able to use the UICR.NRFFW[0] - if I set to the start...
