I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
It is possible to run easily a SoftDevice stack (e.g. S110) on nRF51422 using an accurate 16MHz external clock reference for HFCLK instead of an external 16 MHz crystal oscillator...
Hello,
I bought few nRF24L01+ modules and I integrated them in some custom PCBs that I designed.
I haven't been able to transmit information:
The TX FIFO is full...
I'm working on a very simple Gazell build - basically the gzll_ack_payload example with some of it pulled out, since I'm working on a board with no LEDs or buttons to run...
Hi,
I am trying to develop a PCB for the NRF52 that will use bluetooth capability. However, I was wondering if there were smaller antenna's that could be used rather than...
If I have Bluetooth earbuds, one set to master and the other a slave on my ears.
Is the communication between the ears, through the head, or around the head (Hair scalp...
Hi all
I have two questions/problems regarding the emulated System OFF mode with the NRF52832 and the SoftDevice S132 V2.0.1:
According to this thread , an infinite...
It is to my understanding that you DO have to worry about that when using keil download function or other means to program either the softdevice or your program to the nrf514xx...
hi,
I have created shared channel. currently I only have one master and one slave working.
Master is sending data to slave and it s working perfectly.
But I can not...
Hello,
i haven't found an answer to this question. Which address uses the PTX in Enhanced Shock Burst Protocol (nrf52832, SDK 11)? In the code I found only that:
NRF_RADIO...
Hi
According to the BT spec v4.2, Volume 6, section 4.5:-
"There shall be only one connection between two LE device addresses.
An initiator shall not send a connection...
As show in the title, suppose I have my own bluetooth stack implementation, Is there any possible to flash the bluetooth stack into the nordic series?
Or, another question...
Hello
I'm able to use the MasterEmulator in a WPF or command line application but when I try to use it in Windows PowerShell i get an error.
I'm trying (with the dll...
Hello,
We've been struggling for a while trying to understand how to interpret the nRF52832 electrical specification . Sorry if this may sound like a bad question but we...
Hi, I'm using SDK12 and I'm trying to implement button debouncing. I have initialized one of the nRF52 board buttons using app_buttons.c. In the infocenter I read that debouncing...
Hi!,
I have load Sniffer_firmware into PCA10028 and works, but I can load Sniffer_firmware into PCA10040? it's compatible?
This file --> ble-sniffer_nRF51822_1.0.1_1111_Sniffer...
Hi,
I have tested mbed Classic and mbed OS with CLI and Yotta and works with nRF51-DK and nRF52-DK. Also with Eclipse Neon.1 with yotta build Eclipse CDT4 - Ninja.
But...
