Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
Hi all,
I want to use nRF51822 (s110) to measure the frequency (0 to 5kHz) of a signal connected to an analog input. Other posts ( like this ) show that a good way to implement...
Hi,
SDK:8.1.0
Chip:nrf51822
Power Mode:LDO
Battery:CR2450
Application:beacon
The equipment static power consumption is 3.3 ua, after a period of time is 1.9 ma,but...
I'm using Keil5 to compile example of SDK v12.2. And I'm trying to understand each of Source code to understand how each of it is consists of.
I opened an example "SDK...
My code hit weak handler when I try to modify the examples/peripheral/saadc to run with softdevice s140 on nrf82840 PDK. All I did was adding a BLE Stack initialization before...
On the nRF52832, what is the longest period of time that the softdevice will control the CPU while doing things with Bluetooth? This is effectively the interrupt latency time...
I am working on nRF51 and nRF52 series SoC.
I need to check whether my radio device is connected or not and also to test radio functionality(like radio range, sensitivity...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
Is it the only way to call a function on a read characteristic to make a read request and then inside on_ble_event call the function?
Is this the right way?
Hi
in the communication with an SPI peripheral device, a communication cycle might take up to 5 ms.
It is implemented as a blocking function, meaning that app_sched_execute...
Hi all! Several weeks I've tryed to implement code for my wireless temperature sensor based on nrf24le1 and ds18b20. In datasheet said that in memory retention mode the power...
Hi,
Is it possible to send a advertisements for a single (or a fixed number of) Advertising Events? I need to control the number of Advertising Events "sent" for a mesh...
Hi, I'm looking to build a simple ANT+ application. My only asset for this project is a background in C/C++. I'll need to learn/relearn the basic electronics and protocol...
Hi Nordic,
I have an application that perfectly runs in the nrf51DK but that does not work in my custom board. In my custom board everything else works (i2c, leds lighting...
I understand that in order to trigger bonding procedure you need to read/write a secure characteristic.
I am using the nRF Connect application on IPhone and trying to see...
Hi all,
I need to take samples of a period of two periodic signals and made some DSP processing with both signals.
I need at least 64 to 128 samples per signals.
I...
