Hi,
my name is Nick De Leenheer, and i am finishing my thesis on indoor localisation with CHANNEL SOUNDING. i currently got these outputs in my venv using SERIAL: so i...
Hi,
I´m working on a Zigbee-based environment sensor. You can find all related files here: https://github.com/Kampi/BeeLight
Now I have the following scenario: the whole...
Does the nrf54l15 have a register to specify the boot area? Similar to the NRF_UICR->NRFFW of nrf52833.Or does the nrf54l15 have to boot from address 0x00000000?
Hello,
I've been going through the BLE fundamentals course and things are going well. I'm using the nRF5340DK board and SDK version 3.0.2
I've gotten to lesson 3, exercise...
Hi,
I am working on the channel sounding feature on the 54l15 and I want to perform it sequentially between 3 reflectors and one initiator. I realized that after I make...
Hi,
We're at a point in our project where we're working through some regulatory testing for ETSI/FCC certifications with our BLE dongle board (nRF52840 + nRF21540 FEM...
Hi,
I'm using zephyr RTOS.
I'd like to put the cpu System ON Sleep Mode to conserve power.
Then, I'd like to restart the CPU with an interrupt or event from the comparator...
Hi, I am using a two nRF24L0+'s.
One for TX and one for RX. Transmitting in one direction only. There is sometimes a packet arriving out of order. Every minute or two....
I use ESB sample code ,change to do 8k sample rate ADC(10bit) and transport by ESB ,but overflow when output receive data to PC use uart at UARTE_BAUDRATE_BAUDRATE_Baud1M...
Hi all,
I was trying to test the SDK13 ble_connectivity example being able to compile it when the NRF_SD_BLE_API_VERSION == 4 , but it seems like there are not pc-ble-driver...
I just got my NRF51822-BEACON. I didn't see any LED flashing when I insert the battery. Also I can't find this beacon on nRF Beacon android Application.
hi,
i need to do long process and more flow of functionality that all could stopped by softdevice. so i need to enable and disable soft device. could it could affect my timer2...
hi
here i have use block size 16 byte and block count 5096. this is my start address 0x27000
i have tried to clear 79 pages.
and read data from flash with specific...
Hello to all
I have the next code, basically what it does is reading a button state and if it is pressed then the manufacturer data of the BLE package is lets say B, on...
Hi All,
I would like to know what the default value is for the radio TX power for the nRF5240. According to Nordic's specification, the output power is programmable from...
In the ULP Wireless Q magazine (edition winter 2016), on page 12 / 13 there is listed that the nRF52 chips have a Battery Monitor peripheral but I cannot find anything about...
I have been developing my application using gcc on an NRF52 by putting the text section at 0. This was convenient to get going quickly. We initially weren't going to launch...
hello, i am doing flash read and write in nrf51.for which i have used the C:\nRF5_SDK_12.2.0_f012efa\examples\peripheral\flashwrite\pca10028\blank\arm4 this exampl.
but while...
Hi,
Could somebody share the schematic and board files of nrf51 beacon?
We are planning to make some changes. I don't intend to buy a beacon because I have already purchased...
Hi,
I use the bootloader in the SDK V13.0, I found that no timeout as the SDK v12.x. However, I have added the WDT to the bootloader refer to the link link text
it still...
i could not run timer2 with soft device,. if i start initiaize TIMER2 the bluetooth advertise has disabled. i need this timer to timeout my flow function. i think softdevice...
