Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello all, i made a board with this BLE chip:
nRF52832-CIAA-R
What happens is that when i enable power supply i can see the circuit is properly in advertise ( i can scan...
Hello,
I am currently working with the nRF5340DK and the W5500 shield. Both work perfectly when using the dhcpv4_client application. However, when I attempt to use the recv...
I'm running the peripheral_ancs_client using the 2.9.0 SDK on a nRF5340-DK. On an iPhone running iOS18, the device is not visible under Settings->Bluetooth when the nRF5340...
Hello, I am currently developing a testing software to verify whether all the pins of my module have been properly connected. I configured pin 1.03 as a high level in the...
Dear Nordic Semiconductor Team, I hope this message finds you well. I am currently developing a project called Nuntius Core, which involves controlling bait boats (carp fishing...
Custom PCB with nrf5340/nrf7002. Currently was using NCS2.9.0, with WPA2-PSK connection to the wifi.
While trying to enable use of WPA2-Enterprise, I updated to NCS3.0.0...
Hi Sir,
As we know the nPM2100 support AA/AAA batteries, LiMnO2 coin cells (e.g., CR2032), Alkaline coin cells (e.g., LR44) .
But could nPM2100 support CR123A 1S2P?
...
Hi,
I am using the nRF52840 with nRF-SDK version 16.0.
At random intervals, I encounter the following error:
"[00:02:51.009,460] <error> app: ERROR 1813 [Unknown error...
Hi Nordic team,
I’m using --sysbuild for two examples (peripheral_hr and throughput), but I notice a difference in the build outputs: For throughput, I see both Application...
Hi! I am developing project with nrf connect sdk 2.9.0 on nrf9160 platform. This is multi image project (b0 + mcuboot + tfm + non-secure application). I needed to configure...
I will attach my main.c and skd_conifg, maybe i'm overseeing something in code. Also i will attach schematics and pcb. I'm aware of RGB led consumption, in reality it's around...
Hi!
We use nRF Cloud Log backend in our project. And during my research I found that it actually doesn't filter (despite the filtering code is there) messages generated...
Hello, I'm trying to use BLE on nrf52833. I'm developping with segger embedded studio and I' m usign the BLE peripheral example "ble_app_blinky". Firstly I erased the flash...
Hi Nordic
Is the command:
nrfjprog -s 820100511 --qspiini Qspinrf54l15.ini --qspichiperase --program nrf54l15_FILES.bin --log
We did use it for nRF52840, where able...
I've been able to flash consistently but I finally got my nrf5340 custom board working using Hight Voltage DC/DC by setting it to UICR_VREGHVOUT_VREGHVOUT_3V0, but when I...
