Hi!
I have been unable to find a single, simple set of instructions for adding MCUboot to a project(toolchain 3.0.0 sdk 3.0.0) that will enable a non-default signing key...
Hi everyone,
We're using the "Manufacturer Specific Data" field within its advertising packets to send the firmware version to a phone application. It requires the company_indentifier...
Hi, I am using ncs 3.0.2 and an looking at adding extra .conf files during production. For the app it works fine using --extra-conf, but I can't figure out how to add one...
Hi All, I am trying to write to "adafruit e-link 2.13 Featherwing colour dispaly" from nRF54L15DK running zephyr. With ESP32 i am able to write to the display. But with nRF54L15DK...
Hi, i am looking for basic start up parameters for a 24L01.
I do all my programm in assembler (sorry i am old).
what i aim to do is simple TX-RX, like a small remote...
Hi nordic:
Project MCU: NRF54L05; Development Platform Version: NCS 2.9.0. The APP occupies 220KB of space. adding MCUBOOT and Create an pm_static.yml file in the project...
We are currently using Zigbee Firmware built with nRF Connect SDK v2.7.0 on the nRF5340.
We plan to upgrade the nRF Connect SDK to v2.9.2 and use the Zigbee Firmware built...
hello everyone:
I use nordic APPtoolbox to test DFU ,android toolbox can DFU,but ios toolbox can't DFU
1、 i use sdk9.0 dfu project,and sdk9.0 ancs project
2、 blog.chinaunix...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hi,
Where to get Master Control Panel 3.4.0 source code? Our project is related to creating proprietary BLE profile's. We have some idea on how to program a sensor device...
Hi,
on my board I have a nRF51 and a LIS2DH accelerometer. I want to enable an interrupt pin INT1, so if the LIS2DH sends an interrupt event (pin change from high to low...
I am using example->peripheral->uart(KEIL version MDK 5) in SDK11.0 . Because my 52832 board is a new one I made, I changed RX_PIN_NUMBER and TX_PIN_NUMBER to 9 and 8. CTS_PIN...
Hi,I'm using mpu9150 imu sensor with nRF51822 EK kit, i want read that sensor values i.e acceleration, gravity, yaw,pitch,roll values in keil ide ,how i can do that? Can any...
Hi,i'm using the nRF51822 with the IMU 9150 sensor, i'm using the github.com/.../nrf5-mpu-examples git repo for my sensor. while i try to read the values of sensor in Tera...
I am trying to flash TCP-Server example from IOT SDK from Eclipse.
Project builds without errors.
But I am getting this warning message in Eclipse console when I flash to...
s130, nRF5_SDK_12.1.0_0d23e2a, SoftDevice 8_9_0.
I want to use the Central Glucose Service, how do i modify the "ble_central/ble_app_hrs_c" example code?
int main(void...
I wanted to use MQTT example with nrf52 DK board.
and I uploaded MQTT firmware which is located MQTT example folder in iot SDK.
www.youtube.com/watch
I tried to follow...
Hi,
I want to implement handler for undefined instruction fault. According to Cortex M4 documentation (ARM DUI 0553A subchapter 2.3.2 "Exception types") this fault leads...
Hi everyone,
I've been experimenting compiling my project with Clang and have run into some issues with the supervisor calls and their wrapper in nrf_svc.h.
Without...
Hi,
I want to implement simple module:
gpiote event on pin change (around 6.7MHz signal)
Route gpiote event through PPI to increment counter
Toggle GPIO pin...