Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
Hi.
I wonder if you could help me:
I'm using a thingy91x and would like to work with the npm1300. In the case of this hardware, the PMIC npm1300's i2c bus is connected...
RTT log output issue
Hello, I am using SDK v3.0.2 and toolchain v3.0.2. After building and flashing my firmware, no logs are being output to RTT Viewer. What should I do...
We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
Hi all!
I have the NRF54H20 D and somehow the RTT viewer doesn’t work, the board doesn’t work. I am using the most simple zephyr hello world project. It says it is compatible...
Hi there,
We are using for BLE communication a nRF52832 chip with random static address configuration (shown in the UART). Can we be sure that the address of a chip will...
NCS 2.6.1 + nRF52832
We are using the LIS2DH sensor driver from Zephyr. We observe (and this is also explicitly stated here ) that the sensor initialization is triggered...
Hi,
I'm trying to use MBEDTLS with MBEDTLS_USE_PSA_CRYPTO and CONFIG_PSA_CRYPTO_DRIVER_CC3XX activated.
Unfortunately I can't find a way to tell MBEDTLS that nRF9151...
Hi, I have cloned the channel sounding with range requestor samples but every time I try to build it I encounter the error:
I have not changed the code or anything, but...
Hello Team,
I'm using nrf54l15 dk and ncs version 2.9.0 for the development. I am getting an error while configuring I2C. I selected i2c20 from the device tree and assigned...
I have been testing the thingy91x and measuring power consumption trying to reduce it to the absolute minimum.
Using a test program that moslty sleeps ( using k_sleep()...
Hello, I need help understanding how MCUBOOT produces signed_by_b0_app.hex file from app.hex on the network core of nrf5340. My goal is to have a DFU updatable hex file (net_core_app_moved_test_update...
Hey everyone! I'm working on my Master's thesis about Rust in embedded systems and trying to figure out how much Nordic Semiconductor actually backs the Rust community.
...
Hi Nordic Team,
Setup:
Board: nrf54l15dk
NCS: v3.0.1
I use LOG_INF and printk to print data in minicom or Serial Terminal v1.4.3 from Nordic. Printings seem misformatted...
Hi, I'm working with the nRF9151 DK and currently going through the Cellular IoT Fundamentals course. In Lesson 4 , it states that we should see a message indicating a successful...
Hi
Could you provide what is the max DCR value of L2/L3 10uH inductor in document "PCA20053_Schematic_And_PCB.pdf" that nRF5340 can be accepted?
nRF5340 datasheet only...
Hello! Introduction. Responsibilities of the cores in my device: 1. app core. 1.1. data processing from a stereo microphone 1.2. data sending to net core. 2. net core. 2.1...
I used to use UICR to store the serial number information during the production with nRF52832.
I am working on new project with nRF9151, but when I check the datasheet,...
Hello,
I am new to modems and cellular domain.
We intend to design and build a cellular communication extension for an older product. And I eyed the nRF9151 for that....
