I have a project where we have 2 nrf51 that need to be time synced with eachother.
The problem is they are placed on the body one on the back and one on the chest of a person...
on the page
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fsdk_nrf5_v16.0.0%2Flib_crypto_backend_micro_ecc.html&anchor=lib_crypto_backend_micro_ecc_install
step...
Hi,
In our one of the product we are using Nordic nRF52840 MCU and we compiling this application code in windows with SEGGER Embedded STUDIO IDE Version 4.30a and Tool chain...
Hi,
We made an online course on Bluetooth Low Energy, includes BLE Fundamentals & Architecture, step by step implementation of Environment Sensing service development...
Hello, I am using nRF9160 PCA10090 DK. I want to make my board as central device and scan for all nearby BLE devices and display its rrsi value and device id on a terminal...
Hi Dears,
I have submit a issue for about two weeks but no response yet, would you please help me for handling it?
The link is https://devzone.nordicsemi.com/f/nordic...
It's really really really annoying that the DevZone contains so much outdated infomations and deadlinks .. especially after moving to the new website !!! :-(
Hi,
I am trying to set up a project that continuously measures the pulse width of a signal that may or may not be present at a pin.
I want to use a Timer in capture...
Hey, I am working with the Matter light bulb sample from the 2.9.1 SDK, which I have modified to support the occupancy cluster. (nRF-52840 and nRF-52840DK)
This worked fine...
We're designing a board using the Thingy:91X as a reference design. We're trying to determine the best approach to antenna tuning.
On the original Thingy 91, it uses the...
Hi Team,
I’m using the nRF5340 Development Kit, and in our project, we have a custom slave device that communicates over QSPI. We’d like to interface this custom device...
My firmware is using SDK 17.0.2, and it includes CPS, battery, and a custom service. Everything has been working fine. The custom service is responsible for sending and receiving...
Hello team,
I am using nrf54l15 dk for the devlopment and want to read the RTC counter to check for how much time my device was in sleep mode.
How to achive this?
Thanks...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
Hi Nordic Support Team,
I'm currently experimenting with Channel Sounding using a couple of nRF54L15 boards.
I am trying to obtain raw I and Q samples so that I may analyze...
Hi,
I need to enable an input interrupt on nRF52832 and I want to use a GPIOTE EVENTS_IN channel.
During boot configuration, I'm using nrfx_gpiote_in_init function with...
There are two NUS services here, but only the second one can send data through the RX characteristic. I've checked the source code and nothing has changed. How do I delete...
I recently bought a fanstel blg840 device, and I have programmed At client firmware in nrf91 and custom code into nrf52, but the problem is nrf52 is sending at comments to...
Hi, I want to achieve high speed data transfer between NRF7002 DK with other development board. Therefore, I want to using SPI4 with 32MHz speed. However, I found out that...
I am currently developing a firmware application on the nRF5340 where I need the device to function in dual role :
As a Bluetooth Mesh Node , communicating with other...
Dear Nordic
I use nRF5 SDK BLE_Central / uart to connect our custom peripherals by address, and I found that it seem need to 4~5 seconds to finish connecting
Here is the...
I have modified the NUS-CDC application for the Dongle so that I can now scan, report available Peripherals, and connect to a specific one. I need to be able to cleanly disconnect...
