Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
I am working on an application which sometimes needs to send a buffer of a couple of KB to a connected smartphone using the nordic uart service.
The function used...
Hello all,
I'm currently modifying my Analog Input circuit schematics to improve precision.
I'm adding after my voltage divider, an opamp as a voltage follower to ensure...
i have 3000 bytes of data placed in flash from 0x20000. i want to calculate hmac for the same data.First, can we calculate hmac for such huge data?If yes, then how can i calculate...
I'm using SD 110 and the PCA10001 board.
I make the call to:nrf_gpio_port_read(LED_1), where LED_1 is on, or high. This call always returns a 0. How can I read the state...
Hello!
I'm trying to advertise my custom service. After setting everything up, when calling ble_advertising_init I receive error 0x7.
static m_adv_uuids[] = {0x1523...
Hi,
I ported some SDK code into my device (SDK 10 adapted for S110v7x) where I can successfully Bond my device and use the Services I need (ANCS on my case). I have simplified...
Hello,
I have a project that I want to transfer it from nrf51 to nrf52 (the changes are from nrf51822 to nrf52832). I followed the migration guide. And now it debugs so...
Hi all.
I have phone with nrf Tollbox and central device with DFU, SD130 2.0.0, SDK11.
I would like flash application to central by OTA when I enter password in nrfToolbox...
Hi Nordic,
EDIT: I am using nrf51422, with S210 v5.0.0. Everything that is below is referring to ANT protocol
I want to know if the thing that I am planning to do is...
I download the example of multilink central (S130) into nrf51822 .The central transmit 20 bytes to peripheral interval 50ms sometimes will reset.Anybody know the bluetooth...
Hi guys,
I have the NRF52-DK and want to power only the NRF52. So basically, I want to power it over VDD_nRF.
When I power my DK with a battery and then measure my current...
Hello!
Is it possible to read data sent from ble_app_hrs (peripheral ) to ble_app_uart_c (Central) on PC's serial monitor? If possible, how can i achieve this and which...
Hi,
I programmed nRF52 DK with BLE_APP_UART_SAADC_TIMER_DRIVEN with AIN6 pin as input and is working correctly. But when I programmed the same code in BMD300 the adc count...
I'm running an nrf52832, using SDK 11.0 and the S332 soft device. I've had instances where it seemed my flash data, stored with FDS, was corrupt after a firmware upgrade....
Hi Nordic,
I am having problems knowing what exactly happens in the following situation:
I have a connection established between a master and a slave, and the master...
