Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
Hello,
I'm looking to get XInput working on the nRF52840 so that our device can appear as an Xbox-compatible game controller. I'd appreciate any guidance or recommendations...
Hi all,
It is a common convention to configure the I2C SCL signal to be push-pull instead of open-collector if there are no other I2C masters in the system (saves a pull...
NRF52840
S140
App based on ble_app_multilink_central.
I have tried to build a bridge between BLE peripheral and PC.
I have spend so many time on PC side app.
The...
Hi,
I am building a Thread network ( www.youtube.com/watch with a Rasp Pi 4 as a border router, an nRF52840 DK as an RCP, and an nRF5340 DK as a child to be added into the...
Hello,
Now, I currently run Asset_Tracker_Template on Thingy91X
https://github.com/nrfconnect/Asset-Tracker-Template/blob/main/docs/common/getting_started.md.
And, I...
I have finished developing an application, utilizing the nRF 9151 DK, and I am now working on transferring the firmware to a custom board and testing it. However, when creating...
I can flash the chip. I can run the debugger. I can go to the connected devices, select the device, go to the little "plug" symbol on the RTT, and select it. That brings up...
Dear Forum,
I have an nrf54l15 device and I would like to send a pure sinusoidal tone and measure the phase difference, retrieve I/Q values at the other device. This is...
Hi! I am designing a nRF54 based motion tracker that has an IMU onboard which can take an external clock signal for improved timing accuracy. Initially I had thought of just...
Hello,
I am having an issue using GPIO P0.03 as a button input in my design. Unfortunately, I did not notice that this pin is marked as a dedicated pin for the GRTC peripheral...
Hello Nordic,
We have recently purchased an nRF52840 Dongle. We were able to sniff the BLE packets over the air. So it is found that all the packets that we are able to...
Hi! It seems that I may have uploaded a non-working application to the Thingy91x. Therefore Device is not conectable via USB. The device is responding only in "MCUBOOT" mode...
When Enabling an advertising set already enabled on the Softdevice Controller, the HCI error command disallowed is produced when according to the BLE specification 6.0 it...
I was able to complie many of the nrfx/samples under SDK v2.5.0 using VS Code IDE but cannot successfully compile any under SDK v3.0.0 .
The [Building and running]: <.....
System Info: Hardware: M3 Max OS: Sequoia 15.3 Following the instructions outlined in the readme of: github.com/.../nrf-docker Docker fails to build an image on Apple Silicon...
