But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
I'm using SDK nRF5_SDK_13.0.0_04a0bfd and compiling the example ble_peripheral/ble_app_hrs/pca10056/s140/armgcc using Eclipse Mars 2.
Flashing softdevice s140_nrf52840_5...
Dear Nordic.
I cant found stack API documentation for study.
All company give it for user, for example TI.
User open doc folder and can reed API.pdf file.
Where your...
I use NRF51822_xxaa, sdk12.2, arm_gcc 4.9_2015q3
when i flash hex file experimental_ble_app_blinky_pca10028_s130.hex from C:\NRF\SDK_12.2.0\examples\ble_peripheral\experimental_ble_app_blinky...
Hi,
i have NRF51822 beacon(PCA20006) and NRF51dk KIT(PCA10028).
I am connect a touch sensor and it's gives output in form of "HIGH & LOW".
and i am able to detect the output...
hi,
i want to connect sensor to nrf51822 to send data to smart app continuously over ble.i want to modify example ble_app_beacon. which functions i need to change?
Hi all,
I have implemented a service with various "long char" characteristics. The buffer that I use to receive the data wrote to the "long char" characteristics is this...
I use SDK 9 and nrF51 in the advertising mode. I want to advertise each 1s packets.
First, I call function
set_adv_params(&m_adv_params);
where I
static void set_adv_params...
Hello,
I try to implement the BLE / Cycling Speed and Cadence Service and try to figure out, how to initialize the ble_cscs_init_t data structure. Currently I'm wonder how...
I am building a cadence sensor form the Cycling Speed and Cadence Service module.
Unfortunately the sensor I have built is recognized to have both speed and cadence when...
hi
i flashed s110 softdevice 7.1.0 then ble_app_beacon example application fron sdk 7.1.0 into nrf51822 beacon successfully.but led is not at all blinking in beacon.and i...
Hi
I have got two nRF52840-pdk for long range application design. After reading posts here I realized that the softdevice s140 can only change PHY to CODED after a connection...
Hii guys I am using an nrf51 DK board for my project and I am trying to find the number of advertisements send from the time the board was power up or reset. From my knowledge...
Hi,
I would like to be able to provide a visual indicator such as a blinking LED when the chip is in the Emulated System OFF mode. Note that if the chip is in DEBUG mode...
hi
i tried ble_app_uart from sdk 8.0.0 in pca10028 and it is working.but i want to run it in pca20006.i changed device to 51822 & board to pca20006(in preprocessor settings...
