Hi all,
I have a situation in which softdevice (s310 v2) seems not to forward events to my nrf app (bootloader running dfu) in spite of the fact that my iOS app sees the...
I am sending setup commands to a NRF8001 D device and I receive a command response with status of 0x89. This appears to respond to ACI_STATUS_ERROR_UNSUPPORTED_FORMAT. I cannot...
Hi I'm working on a school project and I need to send data from an accelerometer to a phone I'm currently able to update "dummy" data from my nrf51822 to my phone after following...
Working on an ANT project.
Switched a project from S210 to S310 to add BLE feature.
For the ANT part, there is no source code modification at all.
Sweet.
This is not...
Has anyone experience of successful TICK_DV calibration for nRF9E5? What order of accuracy should be achievable?
In my application I maintain a software RTC clocked by...
Hello,
I manage to work with new S310 V2.
I use S310 for hrm only. Saying so also not for DFU service.
I have own proprietary method for transfering application images...
I am working on an application and need to get the exact time that the master node receive advertising from the slave node. I tried with PPI and it's ok to capture the Radio...
I have a USB HID device using the 'old' USB stack in Zephyr. I have configured the 'CONFIG_USB_DEVICE_REMOTE_WAKEUP'
1. I put the HOST to Suspend
2. The NRF52 USB goes...
Hi,
I am trying to integrate the nRF5340 Audio application (CIS Unicast Server role with bidirectional streaming enabled) from NCS 2.9.0 into on my custom nRF5340 based...
I get error provisioning key on nRF54L15 and NCS 3.0.1. I tried using "Erase all" in nRF connect SDK Programmer, but it doesn't help. Please check also the attached log. nrf54l15dk...
Hello together, Which configurations or setup on the side of the Nordic nrf9161 DK has to be done to use the DEBUG IN connector for SWD? The board is powered by the 5VIN pin...
Hello,
In ncs, I am working with \nrf\samples\ipc\ipc_service. I want MCUboot to build \nrf\samples\ipc\ipc_service\remote to run on nrf5340 CPUNET. When I CONFIG_BOARD_ENABLE_CPUNET...
Hi,
I am working on Temperature sensor MAX30208 using nrf52840 using zephyr. i am working on ncsv3.0.0 . I want to develop a driver for max30208 . can anyone guide me how...
Hi,
I need to use the GPIOTE with interrupt function with nrfx ( https://github.com/NordicSemiconductor/nrfx/ ) directly on the nrf54l15 DK board.
So I created a build...
Dear Nordic DevZone,
I'm encountering pairing issues with mobile devices and a nRF54 DevKit flashed with HCI over UART firmware. After initial pairing, deleting the bonding...
I am trying to get the BMI270 working with a nrf5340 DK. I have read Unable to Connect nRF5340DK with BMI270 Over I2C - Nordic Q&A - Nordic DevZone - Nordic DevZone (nordicsemi...
Device Information
Module: FANSTEL BC832 Bluetooth Low Energy 5 Micro Module
Chip: nRF52832
Firmware version: Default AT firmware
Current MAC Address: ef30:0a:cab132...
Hello Sir,
I am currently working with the nRF52832 (for testing purpose, later will use nRF52833 for final product) as a central device using the nRF Connect SDK. In my...
I have been working with 2.9.1 but went back to a project using 2.6.1 to flash a nrf5340dk and can still compile it, but now cannot flash the nrf5340dk. I am getting this...
I have been testing nRF7002 in STA mode and in monitor mode. Both work fine - but is there a way to have both of them at the same time? Is this a feature that can be implemented...
nRF52810 will not enter deep sleep (system level power management). The method used is through pm_policy_next_state, sleep entry function , sleep exit function, and PM notifier...
Hello everyone. I am trying to develop a emulator for a Bluetooth low energy tv remote using raspberry PI. Basically I want to be able to use the raspberry pi as a TV remote...
