Dear Nordic Experts, This one's a tough nut to crack:
The firmware is based on nRF5 SDK for Mesh 5.0.0 with nRF5 SDK 17.0.2 and Softdevice s132 7.3.0. It runs on a nRF52832...
SoC: nRF5340 SDK: nRF Connect SDK 1.9.1
CMAC calculation works fine with SDK 1.7 and SDK 1.8. But it failed with SDK 1.9.1.
psa_mac_sign_setup returns error = PSA_ERROR_NOT_PERMITTED...
Hi, I'm pretty new to microcontroller programming so please correct my wrongs.
I'm using the Libuarte driver library to have the pca10040 talk to my server via serial connection...
Hello,
Fllow the guide of Configuring and performing DFU over Mesh,I can update firmwre successful use DFU:
Source: Example/Dfu
Target: Blinky(about 180 segment)
But...
Hi,
I need a bit of help to fully understand how ADC works on nRF52832.
I am using a Thermistor sensor like the following to measure temperature:
Epoxy Thermistor...
We would like to use the PPK for automating some of our tests. Is there any documentation on how to drive the PPK over RTT? If push really comes to shove, we can always read...
BLE UART This is a problem that I have discovered while checking
the cause of the connection frequently due to communication error.
It is normal... In the nRF52832,...
Hi,
I added following code in saadc example code to set GPIO pin high/low and monitor it in the terminal. The pull up looks ok, but when I set it to low, the reading never...
We created our own PCB for the NRF52 with a Johanson chip antenna but no matter what we do, we can't get a signal from the Antenna, not even a weak one to show up on the spectrum...
Hello,
I duplicated the project example "nrf51-micro-esb-master" under "proprietary_rf" and got it up and running. I now need to incorporate some timer functionality.
...
Hi. I'm using nRF51822AC, SDK12.2.0, S130 v2.0.1 as central.
As I've tested by using
err_code = sd_ble_gap_address_get(p_addr);
APP_ERROR_CHECK(err_code);
App returns...
hi
i am using nrf51822. i used the radio tranceiver example and it works well. I am planning to advertise the received packets so that the range can also be increased and...
Hi all --
I have a tricky layout "issue" where unfortunately, I've ended up connecting my I2C device to the BlueTooth module on the side of the module where my VDD isn...
I'm reading the SDK 10's GPIOTE doc and I'm wondering if there is a way to read a GPIO state without generating an event, ie, something like foo = PORTx.pin10 or alike.
...
Hi,
I have a central that is trying to pair with a peripheral. I want this connection to be secure and I want to use ECB for encryption of data. My peripheral does not have...
Hi,
I'm trying to communicate the nrf52832 with a LIS2DH accelerometer and when I'm trying to read 192 (32*6) bytes of data (to empty the entire accelerometer's FIFO) my...
Hi,
I want to know what is my execution time for each function.
I am using nrf51822 chip and the IDE is IAR Embedded Workbench.
How can i calculate the execution time...
Can I detect overflow on RTC1 when using timers with S130?
In my App, I use timers but also count time with NRF_RTC1->COUNTER. I need to know If overflow happens.
It seems...
Is it right that this flag BLE_GAP_ADV_FLAG_BR_EDR_NOT_SUPPORTED , prevent my device to be discovered by classic Bluetooth stacks?
Which of these flags do I need to use...
