I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
Hello
I have a problem with my code implementing BLE NUS peripheral. Program hangs in the function sd_softdevice_enable. I have tried with external oscillator and with internal...
My previous product uses an empty notification to indicate that a bulk transfer is finished. I attempted to send an empty notification but got error code 0x10 (NRF_ERROR_INVALID_FLAGS...
I'm using the pstorage driver on the nRF51 to maintain several NVM variables. The NVM functions correctly and maintains state between power cycles. However, when I reflash...
Hello to all Nordic jedi masters!
I am using the nRF52832 along with SDK v11.0
I want to have the SAADC generate events only when the converted value is above a certain...
Hi all,
I am using a nRF52-DK board to receive data from the USB port using Serial, and transmitting it using ESB to a second board. If I use either Serial or ESB individually...
The latest rev of the product spec (1.1 when this was posted) includes a table on page 77 that indicates that the System OFF draw depends on a wakeup source (e.g. GPIO, NFC...
while i open ble sniffer , it sucessfully recognizes the nrf51822 ble nano but when i press w to open the wireshark, it shows no packets and in the interface list it shows...
Example ble_app_uart compiled in Keil 5 O.K but the resultant HEX file in the build folder is only 34K whereas the hex file in the hex folder is 335k. I followed the tutorial...
Hi Nordic team,
Very impressive demo posted on the blog zone this week! I'm trying to understand the details and sorry if I ask something what would be visible in the source...
After upgrading to iOS 10, I have been unable to successfully interact with my device using the NUS. I used to use the NUS to communication with the device and retrieve stats...
Hi, my setup is:
nRF52 DK PCA1040 v1.0.1;
Adafruit MAX9814 electret microphone amplifier;
My project concerns about:
Sampling audio from the board with...
Hi,
I fix bug in original code and managed for nRF51822_xxAB. It is bootloader for application based on SDK7.This bootloader is buttonless and application start after 60s...
Hi all,
When using GCC and Eclipse with SDK 13.0.0 to program an nRF52832 with the Serial and ESB libraries, are there any limitations as to where you can put event handlers...
if i set the attr_md.vloc = BLE_GATTS_VLOC_STACK;
how to set the attr_char_value.p_value?
attr_md.read_perm = p_rrthermomter_init->rrthermomter_attr_md.read_perm;
attr_md...
