در دنیای پررقابت صنعت غذا، موفقیت رستورانها، هتلها، تالارها و آشپزخانههای مرکزی وابستگی زیادی به کیفیت و کارایی تجهیزات آشپزخانه صنعتی دارد. برخلاف آشپزخانههای خانگی،...
I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
Hello everyone,
I’m working on a project using two nRF5340-DK boards to measure throughput and RSSI while dynamically changing the PHY and TX power. I started from the official...
Hi,
When i want to connect my Power profiler kit II to my laptop, it first blinks GREEN. After i connect to it using the power profiler app, it goes: RED -> AMP (Ampere...
I have a custom board with a nRF5340 and need to configure VREGH in DC-DC mode and set 3.0V output on it.
I see the documentation on REGULATORS — Regulator control where...
Hi Nordic Expert,
Recently I wanna run ble_nus service on my nrf51822 platform, you know, sdk 6.0 does have this demo code in s110 directory, but from sdk 6.1 I cann't...
I'm trying to connect to/program my nrf51822 module I just got. I've got it set up with my st-link but whenever I try to flash the device I keep getting: Error: Flash Download...
I'm trying to enable basic commands with my device. Ideally I have a terminal open on a mac running nodejs or use the UART subapp in the nRF Toolbox App, type a special command...
What's the proper way to debug what's causing my eval board to reset? I'm assuming I need to put a breakpoint in the hard fault handle, but how do I trace that back to the...
Hi,
as a university project, I am currently developing a ultra-low-power temperature and barometer sensor powered just by RF and laser-beam energy. Please see this link...
Is there any document that describes what has to be done in the App code to migrate from i.e. SDK v7.2 to the latest 8.1.1? I could not find it.
Ideally it would be nice...
I try to add a custom characteristic value's UUID. I couldn't find any example or document that provide this information. All I can find is a function sd_ble_gatts_descriptor_add...
As I run through the examples for the nRF51 S110 SDK , I'm not seeing anything for communicating with a sensor over I2C.
On a secondary note, since I have the option to...
I am using a nRF51422 (SDK 6.1.0 with S310) and i have a question about th UART.
I can send and receive data from/to an other MCU but i have to set different parameters...
Hi,
I recently started learning to program nRF51 development kit. I followed most of the examples listed in the forums but I am unable to find a dedicated link which would...
Hello,
I have made some modifications to the OTA DFU bootloader provided by nordic and would like to some advice. I went down this design path before nordic released the...
I was disappointed to see from this question that when calling sd_ble_gatts_characteristic_add(), the value of the characteristic is copied to the SD's memory region:
devzone...
Can anyone explain what that error code is meant to mean?
With the example sdk7.1 dfu bootloader, hrs_with_dfu app built unmodified and sd110 7.1, I get this error on attempting...
Hello,
I have a BLE application running on a nRF51822 chip with the S120 softdefice. If I use the standard Android "search for device" mechanism for Bluetooth devices,...
