It is nRF54L15 + SDK 3.0 + Matter application.
I have developed a custom BLE service that is based on Nordic's proprietary NUS BLE service. The BLE custom service is enabled...
I am trying to get a WiFi project working using the nRF52840DK and nRF7002EK . I use a 3.3V power source that is supplying power to both nRF's in parallel. For the nRF7002EK...
Hi,
I'm developing firmware for the nRF52840 DK using nRF Connect SDK v2.9.2 , and I’m running into a problem that didn’t occur in v2.8.0 .
My project uses Zephyr and...
I am receiving an error when connecting to a custom board by running nrfjprog --reset, any similarly with any other commands that require connection.
I am connecting through...
We have previously used nRF52840 and for the latest iteration of our board design we are updating to use nRF54L15.
We are aware that for nRF52840 we could map any pin to...
Hi,
I faced with an initialization issue of combination two features: MCUMGR and UART_ASYNC_API. I get a crash right after the FW starts. It looks like the SW configuration...
I checked the nrf52832 manual and found that both XC1 and CX2 are analog input pins for the 32Mhz clock pin configuration. The reference design for both uses 32Mhz crystals...
Hi,
Good day!
I tried to add the RTC2 driver to our application and i keep getting this compiler error message (using sdk16.0).
Here is my sdk_config.h. Not sure why...
Hi
I'm planning to connect three different BLE peripheral like Heart-rate sensors, Health Thermometer, and Blood Pressure to a Central BLE device.
I'm using a small customized...
Hello
What is the specified max current on the supply pins for nRF52840?
The GPIO pins are specified to source max 14mA in 'high drive' mode:
How many of these pins...
Got called back to an old product that used nRF24LE1. Need to do a simple hot fix.
But I don't have the nRF6700 Dev Kit with me anymore. It cost almost $600 to get one from...
To the kind attention of Nordic support team,
I know that gazell secured libraries are available at least for keil compiler and nRF52840 device.
Are those libraries available...
Hi,
We are seeing a voltage of approx 1 volt on our USB connector when USB is not being used (VBUS).
We are using our device in a Wet environment; this voltage between...
Hello,
I am using nrf52840DK and I try to send data from sensor to ble toolbox. I want it to advertise for 1 minute and then go sleep for 5 minutes and do it again and again...
Hello dear Nordic Semiconductor. I use one of your creation - nRF52840 USB dongle. I have troubles with using USB CDC ACM. I add ble stack to gather info about advertisement...
Hello,
I want to do fast advertising (100ms) (LE privacy enabled) for about a minute, then I want to transition to slow (1000ms) advertising forever (or until a connection...
To the kind attention of Nordic support team,
I'm porting old code in order to use nRF52840 and s140 softdevice. During initialization of device information service I have...
i've been trying to update certification on the device (fallowed the guide https://devzone.nordicsemi.com/nordic/cellular-iot-guides/b/getting-started-cellular/posts/nrf-cloud...
Hi there!
Working with the nRF52840 DK, I am wondering how I might modify an existing SDK example in order to display the Tx and Rx Power characteristic on a hardware connected...
Dear I would like to put the license key to nff5-SDK examples into sdk_config.h file Format on thisiannt side looks like this 0xXX, 0xXX, 0xXX, 0xXX, 0xXX, 0xXX, 0xXX, 0xXX...
Hi I tried modifying the ble_app_uart_pca10056_s140 example as follows (nus_data_handler method modified only) such that it echoes the data back sent from the phone:
I...
Hello to everyone,
I was told to develop a simple BLE scanner using NRF52 DK (NRF52832). The idea is just to identify surrounding devices but we don't want to initiate connection...
