I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
Hello!
We are trying to get low average current consumption on the nRF9160 DK without success.
The floor current between modem active time is ~60uA, which is fine. But...
We've recently been testing the accuracy of the GPS on our devices. My basic method has been to trigger on GPS_TRIG_DATA_READY/GPS_CHAN_NMEA, and at each trigger fetch both...
I would like to advertise some sensor data (temperature, humidity, pressure, co2, voc and other) by BLE advertising packet without any connection. I know, I can put it data...
How much ram is my application + Zephyr + modem firmware using and how much is available in the nRF9160? I'm unable to find a memory map and anyway that wouldn't include dynamic...
Can we alter the eddystone tlm (telemetry) packet to send custom data . [This is not following the standard packet structure].
But I wanted to know how to alter the given...
I need a product that will allow me to connect a PC to a Bluetooth device through its Bluetooth connection. I will need to be able to send data bytes from my PC across the...
Hi everyone,
I am a beginner with Nordic SDK. I followed the " Getting Started Assistant" and then try to open asset_tracker project on step 4. During the opening I got...
Hello,
The fds.c fds_register() has suspicious usage of atomic variables.
It is first checked if there is space in the m_cb_table, then m_cb_table is modified and only...
Hi, I am trying to add timer information to the sending packet. We created some space(manuf_data) to store data. However, the problem is we do not know how to put actual-time...
Quick Summary: - Devices used: nRF52832 (Central), nRF52840 (Peripheral)
Example based on : BLE Scanner
Hi Team,
In my current application, based on a BLE Scanner Example...
Hi,
I'm using the latest SDK v16. I got the following error when call peer_manager_init()
<debug> nrf_ble_lesc: Initialized nrf_crypto. <debug> nrf_ble_lesc: Initialized...
Is there a recommended way to inspect the state of the heap? I haven't found anything obvious yet. I'd mainly like to know the amount free, the largest block, and perhaps...
Hi,
I start developing with ble_app_template and DK
I combine uart spi twi into it
It can connect to my phone(nRF Connect APP)and work fine on DK
However when i use...
We want use Nordic chips as the transfer medium for our data frames in mesh-like network.
So we don't need ATT,GATT,GAP,SDP,SMP and all high-level things.
As I can see...
