Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
I am using the heart rate example to do a quick demo. I am sending a short string of data one byte at a time to the iphone. I decreased the HEART_RATE_MEAS_INTERVAL interval...
Hi guys,
I have the nRF51 Development Kit, and I am trying to develop on my mac using GCC and eclipse. However, the tutorial I found either incomplete or outdated. I tried...
I want to bring up my own new board, but the nRFStudio can not connect to the J-Link, please check the picture.
I connect 4 lines from board to J-Link, including VCC, GND...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
I haven't seen any posts about this, so I thought I'd post what I observed and how I fixed it in the hope this helps someone else.
My nRF51 DK (PCA10028 v1.1.0) out of...
I have gone through most of the guides/links that I saw here to no end.
My development environment is OS X 10.9, gcc-arm 4.9, nRF51822 beacon.
Before going for the IDE...
Hi,
I am trying to build a low power device using the nRF51422 SoC without a Soft Device. I need a timer to occasionally wake up the chip and as I read the product specification...
I have a basic question regarding a basic area. Interrupts! But without any good specification and how the OS work and good example how to do this I need to push for the obvious...
In ble_dfu.c (unmodified SDK 8.0.0) I am unable to get the buttonless DFU hooked up.
For reference, ble_app_hrs with s110_with_dfu works correctly. I have traced my issue...
Hello,
I am trying to write data to flash with the pstorage api. I managed successful to write data to flash with the pstorage_test_store_and_update() function from the...
I am searching a cheap wifi solution and this NRF24L01 communicates through 2.4GHz network, therefore it may be compatible with 802.11 protocol and further with TCP/IP protocol...
Hello!
We're using PPI to connect one pin to clear and capture events on Timer2. On pin low-to-high we're clearing the timer and on pin high-to-low, we're capturing the...
Hi,
I am planning to use nRF51822 for one of our projects.
Can you please hlep me with the SDK that will support IAR Embedded Workbench.
Thanks & Regards,
Sumit
