Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi, I made a beacon board only have button and leds. The version of chip is nRF51822-QFAA G0. I used the precompiled hex file in the nRF518222 Beacon v1.1.0. After I download...
Hi,
I am trying to debug a custom PCB for the NRF51822 - I can run a modified version of the HRS application (S110) that has been verified on the PCA10004. The LF clock...
hello, my name is alessio and i'm italian. I have got a problem with "RFduino" and the "pulse sensor amped" ( heart rate) .
I downloaded the library of the sensor in the...
Hi,
I have a few questions about the SPI master module. I'm using it for an application that basically needs to be gapless. After quite a bit of work, I've gotten it to work...
Hi, I am evaluating the nRF51822 for an ultra low power energy harvesting application.
I measured the time from power-on (VDD applied) to code exectution (GPIO toggle)...
Is it possible to launch ipv6_coap_client on nRF51822-EK?
I have modified preproccessor simbols adding BOARD_PCA10001 instead of BOARD_PCA10028.
Also I modified part concerning...
Hi
Can anybody answer me if i do not call SOFTDEVICE_HANDLER_INIT instead i call sd_softdevice_enable ,sd_ble_enable(&enable_params),sd_nvic_EnableIRQ(SD_EVT_IRQn) directly...
I have a simple project which uses S110, so I flashed the S110 and the bin, but the result is not as expected (blinking LEDs), is there any quick way to verify before needing...
hrs_sdk7_1_bin_sc.zip contain application.bin and application.dat
How can I make a xxx.dat file?
When I del it from zip,it will cause error during dfu update.
Hello EveryOne
My button event handler is not being called. following is my code what can be the problem.
uint32_t err_code;
ble_stack_init();
timers_init...
i am working with eclipse. i want to create a binary file. after successfully creating the .elf file eclipse displays a make error saying region ram overflow by so and so...
Hello,
If I enable POFCON at 2.1V threshold in my S/W, build and download it in my target, and I turn on n51822 at VDD is 1.8V. That is, VDD is lower than POFCON threshold...
Hi ,
Could anybody share me the details on the time taken by the nRF51822 to comeout from reset state for the below reset input.
Wakeup from OFF mode reset
Pin...
Hi...
I started with S130 demo example code. Added a custom services . The problem I am having now is that after I connect ble_evt_dispatch isn't being called.
I have...
Hi, I have purchased a Nordic nRF51 and start to write my firmware using mbed OS compiler. As far as I can see the whole process was working perfectly. I could update the...
