Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I'm trying to solve an intermittent problem when using the nRF51422 UART with CMSIS-RTOS (RTX) and MDK Networking library (V6.2) (TCP/IP stack).
My questions relate to...
Dear all,
I am a little confused about erasing data contained in a flash block. In this link the clear example shows that it is possible to clear bytes from a specified...
Dear all,
I have been trying to get the ADC BLE example working, given at github.com/.../nrf51-ADC-examples
I noticed it gave me error with SDK 6.0.0 saying ble_enable_params_t...
I have been working on ANT for a while on battery powered device. Now because cell App is involved in my project. I want to quickly gain some hands on data on BLE power consumption...
Currently, the Bluetooth communication TEST in progress.
I am using the example experimental_ble_app_uart_s110_pca10028
Applications are received by the data nRFUart2...
Hi...
When i was working in SDK v6.1.0 i have tried nrfprog.exe to merge and program bootloader, softdevice, application and bootloader_settings file as explained in devzone...
I am using two nrf24l01+ at two ends & i am able to communicate between both but its a simplex communiacation means I am transmitting nrf code from A end & B end receives...
After programming a panel of 6 modules embedding nRF51822, I would like to send some data in order to test some features. The basic idea is to validate the modules before...
Hi,
How can I change/add include file path in the new pack SDK.
For eg: I want to port the S110 bootloader to S130. But I am not able to change the include path to the...
I am using LMT84 temperature sensor directly connected to P06 on my nRF24LE1, QFN24. Using the built-in BG reference of 1.2V, I measure temperatures from about -30C up to...
When I call the function sd_ble_gatts_sys_attr_set, the compile error "source\ble.c(142): error: #165: too few arguments in function call" showed in Keil V5. But I found just...
Hi,
I have used the following version for my development
SDK: 6
SD:s110_nrf51822_7.0.0_softdevice
nRF51822 :3.0
Recently we are using nRF51822 3.1 QFACA1 1442AB...
Hi,
I am trying to setup DFU on a PCA10001 board with the following specifications:
softdevice v8.0
bootloader: From SDK v8 examples (bootloader\pca10028\dual_bank_ble_s110...
I updated my MCP to the newest version and then the new MCP wanted to update the pca10000 with the newest firmware--> failed. Now i can't get my pca10000 to work again. i...
