Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi,
I'm working with an SPI FLASH chip that has a page size 256. I noticed that when I call nrf_drv_spi_transfer() , the rx length of 256 rolls over the uint8_t container...
Why the SPI clk doesn't work, i checked using an oscilloscope :/
I also don't get any SPI interrupt and no data change in the RX buffer although I have wired MISO and MOSI...
Hello,
I just encounter a compatibility issue between the two SDK (11 Vs 12).
So i have so product on the market base on SDK V.11.0.
I m developping an update based...
Currently I am facing strange issue in my project. Let me first highlight my set up. I am using the PCA10040 kit for development, keep multi-meter in series to measure current...
hi experts, I want to build a ble center based on s130 to collect sensor data from several peripheral devices. Some of them may not be from nordic solution, such as TI. so...
When I connect to my firmware after cycling Bluetooth on iOS, I am able to subscribe to my Characteristic Indications without any issues. The nRF connect app receives all...
I have two boards, one is official demo board, the other I make PCB board.
I down the open-mesh source code form github.sdk version is 8.1,open mesh stack version is 0...
Hi,
I have to send data with notification from central to peripheral, because I need save some data in peripheral device.
What I have to do ?
I test it on Adnroid 4.4 ...
Hi Sir,
I am working on nRF52832 board with pca10036 cortex M4, and i worked out spi master and slave example code on a same board and configuring spi instance 0 as master...
when using secureDFU with sdk12.2, only changed the mac address.
my application is more than 60KByte,
when i test the firmware for two files, one is 62K and an other is...
hello, im from india im using nrf24l01+ for my project to transmit and receive data between two arduinos. i tried all tutorial basic programs but i cant sucessfully send and...
I made a BLE peripheral (nRF52 + SDK11.0.0 + s132) and have so far been using Android devices (that supports 7.5ms connection events) to connect to it. I want to connect to...
Hello,
We are sharing SPI and we found possible bug in nrf_drv_spi....
The problem was that first SPI is using blocking SPI thus does not use ISR and set it to NULL: ...
