Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hi
I use nRF52832 and SDK13 and Central Device project.
and my device has not bonding function so may I mask my central device pm_conn_secure call
here is my part of code...
Hi,
I got the nRF52840 preview development kit and I am trying to follow the quick start guide here:
link text
It works fine for me up to step 7, where I am supposed...
Hi
I have gotten a Nordic PCA10040 hooked up to a Sparkfun nRF52832 as described near the bottom of the page here: learn.sparkfun.com/.../nrf52832-breakout-board-hookup...
hello,I'm having a problem with the ANT application,I have two pieces of the PCA10040 board as a ANT connectivity board for a ANT application board.According to the instructions...
Hi,
what is the default tx_power value in new v13.0.0 SDK in the ble_app_att_mtu_throughput example?
I can't find the use of the sd_ble_gap_tx_power_set() function which...
Hi,
After configuring the nRF51422 as a SPIS slave 0, we get the following error when trying to create the slave instance:
static const nrf_drv_spis_t spis = NRF_DRV_SPIS_INSTANCE...
Do you have any ready made example where beacon and NRF52 DK are communicating will each other.
Our idea is that beacon sends data to the NRF52 DK and NRF52 DK sends the...
Sorry if this is obvious but I cannot find the units of nrf_esb_config_t::retransmit_delay
in the SDK documentation, it just says: "The delay between each retransmission...
Hej,
I'm working with the nRF24L01+ and the ATmega328p programmed in c. The goal is to have both TX and RX mode in the same device, mainly work as RX but in certain conditions...
Dear sirs, I've had a difficult time establishing communication between my nRF24L01+ board and the SPI bus on my Arduino Uno R3 microcontroller. Could you please provide me...
Hi all,
I am thinking of using a GPIO pin's "SENSE LOW" to wake up my device from SYSTEM OFF mode.
In order to avoid the device keeps waking up in case the pin stays low...
I am using an nrf51822 DK with a (so far) very simple code along:
main()
{
//... init I/O
run();
}
Inside run:
run()
{
uint32_t retval = NRF_SUCCESS;
...
