I would like to source a compact BLE board to act as a lock controller developed with with a matching transceiver for use in a fob and an app.
It would toggle the pio and...
Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
Hi All,
In my application I have two analog inputs coming from two different sources that I have to sample using one SAADC present inside NRF52. As far as I know, NRF52...
Hi,
I'm using nRF5 SDK V12.0, I found a strange problem. That is the UART can send data to PC, but it cann't receive data from PC. However, this problem just arise on some...
Hi,
I need a bit of help to fully understand how ADC works on nRF52832.
I am using a Thermistor sensor like the following to measure temperature:
Epoxy Thermistor...
We would like to use the PPK for automating some of our tests. Is there any documentation on how to drive the PPK over RTT? If push really comes to shove, we can always read...
BLE UART This is a problem that I have discovered while checking
the cause of the connection frequently due to communication error.
It is normal... In the nRF52832,...
Hi,
I added following code in saadc example code to set GPIO pin high/low and monitor it in the terminal. The pull up looks ok, but when I set it to low, the reading never...
We created our own PCB for the NRF52 with a Johanson chip antenna but no matter what we do, we can't get a signal from the Antenna, not even a weak one to show up on the spectrum...
Hello,
I duplicated the project example "nrf51-micro-esb-master" under "proprietary_rf" and got it up and running. I now need to incorporate some timer functionality.
...
Hi. I'm using nRF51822AC, SDK12.2.0, S130 v2.0.1 as central.
As I've tested by using
err_code = sd_ble_gap_address_get(p_addr);
APP_ERROR_CHECK(err_code);
App returns...
hi
i am using nrf51822. i used the radio tranceiver example and it works well. I am planning to advertise the received packets so that the range can also be increased and...
Hi all --
I have a tricky layout "issue" where unfortunately, I've ended up connecting my I2C device to the BlueTooth module on the side of the module where my VDD isn...
I'm reading the SDK 10's GPIOTE doc and I'm wondering if there is a way to read a GPIO state without generating an event, ie, something like foo = PORTx.pin10 or alike.
...
Hi,
I have a central that is trying to pair with a peripheral. I want this connection to be secure and I want to use ECB for encryption of data. My peripheral does not have...
Hi,
I'm trying to communicate the nrf52832 with a LIS2DH accelerometer and when I'm trying to read 192 (32*6) bytes of data (to empty the entire accelerometer's FIFO) my...
