Hi,
I use the nrf51422 chip.I want to know if the ANT establish link between chips,where can I get the matching configuration (like device type、channel ID).I mean is...
Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
I have set up the NCS toolchain, followed the instructions to update the JLink DLL in SES, and successfully built/flashed a few examples to the app core (ie. debug/ppi_trace...
I would like to send TCP message with 50KB message size. I saw that maximum size was limited by CONFIG_HEAP_MEM_POOL_SIZE which was 16kB.
Is there any way to send that message...
Hi,
we are experiencing unexpected behavior during sleep entry. Following pictures were taken using an oscilloscope, our device sends a radio transmission every 150 ms...
Hello,
I am trying to sample and reconstruct an audio signal using the SAADC and I2S respectively. I have a double buffer setup for the SAADC, where we process the data...
Hi,
I've noticed several times now when the NRF9160 comes out of a PSM sleep cycle that when a call to an underlying socket connect(), or nrf_getaddrinfo() call (whether...
HI,
I am developing an application with 7 transmitters and 1 receivers. Transmitter are nrf52832 with MPU9250 IMU (Holyiot YJ-18008) . I am hopping to each transmitter...
I successfully compiled and loaded the UART/Serial Port Emulation over BLE example on an AdaFruit Feather board.
I can connect to the Nordic UART Service, then send data...
I have built my application on ble_app_uart in keil in SDK 14, so I just did the same and copy-pasted my code into the latest ble_app_uart example built with ses in SDK 16...
So far i've failed to find a single source that contains comprehensive information on where errata items have been addressed. I do have multiple unrelated sources for information...
Hello, I want to try the secure bootloader + softdevice 7.0.1 + ble app buttonless dfu example from SDK16 I want to test all that in our custom board NRF52832-QFAB (256k flash...
Hello, I modified the ble_app_blinky example to work on our board (removed leds and buttons) and modified the board pca10040.h the new application worked on the devkit but...
Hello, I am completely new to embedded software development (so far I have been using development boards such as Teensy, Feather and Arduino) and I recently acquired the BLYST...
Hi
I'm currently look into the noise floor of the SAADC samples on a custom PCB with a nRF52
I'm running the ADC at maximum sensitivity (4x gain, Vref=0.6V) differential...
Hello
I have a power constraint device. Limit is not the total charge of a battery or so. Limit is the peak current.
Available (peak) current is around 4mA (@1.8V), current...
Hi,all. i face a problem that i used lightblue on iphone6(ios8.3 12F70) to connect my device(nRF51822),after sometime,disconnected automatic.
lightblue says:The connection...
