Hello,
We have the custom board with nRF54H20. The VDD_EXT pin is used to power some GPIO ports of nRF54H20 (P1/P2/P7).
The voltage we see on VDD_EXT is about 1.3V instead...
Hi,
I want to test the behavior of Enhanced Multi-Admin added in Matter 1.4.
Is it possible to verify this behavior using a Nordic DK board, sample code and a Raspberrypi...
I've been able to flash consistently but I finally got my nrf5340 custom board working using Hight Voltage DC/DC by setting it to UICR_VREGHVOUT_VREGHVOUT_3V0, but when I...
Hi,
I had a working project for nrf Connect NCS 3.0. I don't know what happened, but now I can't even create a new build configuration. Every time I click on "add build...
Hello,
Please forgive me for this question. I am an extreme noob. And am trying to get started with my first project.
I am working with the nRF52840 DK, and I am trying...
Hi,
I am trying to make the nrf52833 into an Auracast broadcast receiver (for a broadcast from my phone).
I am using bindings to the softdevice controller ( https://github...
Hi Nordic team,
I tried to view logs from my custom nRF54L15-based MCU using J-Link RTT Viewer, but it's (printk) not working. The same prj.conf configuration was previously...
In Mesh SDK, there are 3 versions available for s132 softdevice: s132_3.1.0, s132_4.0.4, s132_5.0.0.
The question is, should I always use the latest version available? If...
Before I use 51822QFAC(with 32K RAM)， add I must use 51822QFAA(with 16K RAM)。
I have modify IRAM area，like this
IRAM: 0x20001FE8 0x2018.
and selete device is 51822QFAA...
We are designing the nrf52840 with high voltage mode and both DCDC regulators.
Where can I find the requirements for the external circuitry, like the inductors. For now...
Hi,
1. what the DC2DC switching frequency of nRF52832?
2. at nRF52840 the inductor should be 10uH with tolerance +-10% but for nRF52832 this inductor can be with tolerance...
Hey everyone,
I've been trying to get this basic bare-metal application to work. I don't need a softdevice as I'm just trying to turn on an LED. The application compiles...
Could not connect to the nRF52840 preview DK eval kit running the ble_peripheral/ble_app_uart firmware to iOS 11 device running the nRF connect or toolbox apps. We tried on...
Hi:Nordic
Because the nrf52832 can't read 8bit parallel data from GPIOs to RAM with EeayDMA . So I want to use 3 SPI simultaneously to write data to ram with EeayDMA, can...
Hi there,
I have a issue with the nrf51822 UART baudrate setting.
I am developing nrf51822 dongle, its job is to transfer data between PC and a BLE periph. For a stable...
Hi, is it possible for the 824 chip to sleep until woken up by the Bluetooth of a nearby device that wants to connect/pair with it? And what would be the current consumption...
Hi,
As part of my watchdog flow, I'd like to test the liveness of the softdevice and the SDH during operation.
Is there a built in way to trigger the softdevice to post...
Hai
whether Bluetooth 5.0 in nrf52840 Compatability with Bluetooth 4.2 available on my phone, I heard that Bluetooth 5 is lower compatible. I like to know whether it has...
I am looking a way to send a string without the terminal, ble_nus_string_send function only works in the uart_event_handle() and APP_UART_DATA_READY is only triggered when...
I am writing a library for Nordic nrf52832 and it uses some of the functionality from fstorage ( fstorage_nvmc implementation) to access the NVM. The library creates only...
I have some functional code working on an Adafruit nRF52 Feather board which I am trying to change over to run in embedded C on an nRF51 dongle. I am using Adafruit nRF52...
Good evening, I'm trying to understand how to use the SDK 12 to connect peripherals using PPI such that when an address match occurs (say on pipe 1's address+prefix), a timer...
