I will be selling various ble products. My customers can connect to and program the devices using their bluetooth smart phone or tablet.
I want them to have the option...
Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hi. I have a question about Bluetooth 5.1. I just want to know what the main difference is between a Bluetooth 5.0 and Bluetooth 5.1 chip.
Is it the hardware or software...
I am developing a firmware on a nrf52840 board with FreeRTOS. Unfortunately, due to a mistake during the development process, the board misses the XTAL 32,768 Hz.
Is there...
Hi Nordic:
I want to build a raspberry connected to a 52832 board via uart,
this raspberry pi with 52832 board need doing secure DFU to remote BLE device, the raspberryPI...
Using the nRF9160 on the Verizon network we are having some issues with eDRX. Specifically sending data to the device from our MQTT server.
We have configured a eDRX interval...
Hi,
I am working on nrf52 msc example. I am required to use internal flash for msc. In example there is support for ram, sd card and spi flash. I am required to use internal...
Hello,
I'm currently trying to sniff the DH Key Exchange as specified in Spec 5.1 p.2446. I'm using the nRF51 Dongle as sniffer, the nRF52 DK as slave and the nRF52840...
Hi,
I am using two nRF52840 DK in which one of the board is flashed with light switch client and other one is flashed with light server and a nRF mesh app is used for provisioning...
Hi,
I see Nordic has recently released an updated software to do direct test mode (without the use of python or the old nRFGo studio). I am able to run the test code on...
Hello,
I am using nRF52840, SDK_16.0.0, S140 SoftDevice and Segger 4.16 for flashing the image.
1) While upgrading over serial interface using DFU, whether UART needs...
Hi,
If you are interested I would to contribute to https://github.com/NordicSemiconductor/nRF-Sniffer-for-802.15.4 repository. On the python driver part. You could allow...
Hello
I'm doing a test that if it's possible to start ibeacon function when BLE is connected in nRF52840. so I merge ibeacon into HRM demo code and as you can in the following...
Hello ...
Our BLE peripheral product (nRF52810, SDK 15.3.0, SD 112 6.1.1) is relatively simple. iOS device (central) connects to peripheral. Data is exchanged between the...
Hi, i'm new to Nordic devices and i hope this topic hasn't already been treated. I'm triyng to debug an example application; after the first breakpoint, i loose the control...
Hi,
I try to set the TX power of the NRF52833 to the maximum possible power level, but somehow nothing seems to affect it.
I first tried to change it in the sdk_config...
In spec, 9160's PSM current is 4uA/3.7V.
However, When I use a same PSM code.
On our product. We measured is 4.5uA/3.7V and 5.5uA/3.7V. And on 9160DK, the consumption...
