Hello,
We have the custom board with nRF54H20. The VDD_EXT pin is used to power some GPIO ports of nRF54H20 (P1/P2/P7).
The voltage we see on VDD_EXT is about 1.3V instead...
Hi,
I want to test the behavior of Enhanced Multi-Admin added in Matter 1.4.
Is it possible to verify this behavior using a Nordic DK board, sample code and a Raspberrypi...
I’m writing BLE UART code. When BLE is not connected, current consumption is ~30 µA. But when BLE is connected, consumption increases by ~1 mA. I want to reduce the current...
Hi Sir,
As we know the nPM2100 support AA/AAA batteries, LiMnO2 coin cells (e.g., CR2032), Alkaline coin cells (e.g., LR44) .
But could nPM2100 support CR123A 1S2P?
...
I've been able to flash consistently but I finally got my nrf5340 custom board working using Hight Voltage DC/DC by setting it to UICR_VREGHVOUT_VREGHVOUT_3V0, but when I...
Hi,
I had a working project for nrf Connect NCS 3.0. I don't know what happened, but now I can't even create a new build configuration. Every time I click on "add build...
Hello,
Please forgive me for this question. I am an extreme noob. And am trying to get started with my first project.
I am working with the nRF52840 DK, and I am trying...
To the kind attention of Nordic support team,
I'm evaluating your standard gzp example (proprietary_rf/gzll/gzp_dynamic_pairing, sdk15.3). From what I see, the device to...
Hi,
It seems that the nRF52811 for the most part draws less current the nRF52832. For example:
nRF52811: 1.4 μA at 3 V in System ON mode, no RAM retention, wake on RTC...
Hello,
I cannot reset the nRF52 DK while running on battery power. I've tried multiple examples of the SDK which didn't work. However, when connecting the DK via USB, the...
I don't know if I'm dealing with a hardware or software problem at this point. I have a custom NRF52810 board with chip antenna and no LF clock, in SES. In SDK 16 I modified...
I'm running the esb_ptx_pca10040e on a custom board with NRF52810. The program gets stuck on....
while (NRF_CLOCK->EVENTS_HFCLKSTARTED == 0);
This appears to be similar...
Hello,
I am using nRF52840, SDK_16.0.0, SoftDevice S140 V7.0.1 and Segger for flashing the image. I am using ‘ble_app_blinky’.
1) Previously we had a custom board...
Hi,
I was testing the various cases for DFU & I was looking for any possible solutions to fix the issue.
I flashed SD + bootloader (secure) + app from SDK 15.2 on the...
Hello,
I´m trying to update the certificate of my nRF9160-DK. To do this the modem has to be in offline state. I´m running the AT Client sample like it is shown in the chapter...
I am curious if there is an inherit maximum transmit duty cycle of either M1 or the nRF9160. I am asking for this because we need these numbers for SAR test. Our product will...
Hi All,
I am working on a project with NRF52840 , we are looking for a solution to do the OTA to device by the central device , both of them are using NRF52840 as BLE module...
Hi, I need to be able to count the number of packet Tx and Rx from one board to another in order to compute a packet loss ratio for certification purpose. To achieve this...
hi all:
Use PPI+timer+adc, in the following ways:
called stop, then unable to start adc, Couldn't get into the NRF_DRV_SAADC_EVT_DONE.
Could you tell me how?
Hi,
My product is undergoing susceptibility test and strange issue is happening after the test for 1-2 hours, ie while trying to send data with higher MTU size notification...
