Hi ,
I would like to know if a matching network is needed if I am only using a single external flex antenna for both LTE and GPS using a RF switch between them and a uFL...
I am a student interested in Nordic.
My coding skills are very poor.
So I want to get help.
I want to use the vl53l1x sensor in nrf52. (My ultimate goal is to measure...
I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
nRF51822
S130
SDK11.0
The power consumption immediately going up high to 1MAH once I enable TWI using this code:
NRF_TWI0->ENABLE = TWI_ENABLE_ENABLE_Enabled << TWI_ENABLE_ENABLE_Pos;...
Hello,
When I added the below lines I get some error:
NRF_BLE_GQ_DEF(m_ble_gatt_queue, /**< BLE GATT Queue instance. */ NRF_SDH_BLE_CENTRAL_LINK_COUNT, NRF_BLE_GQ_QUEUE_SIZE...
Hello,
I have been looking through Nordic's documentation for the nRF9160 and trying to find voltage ranges for several pins but am having no luck. Can someone please answer...
iOS is using queued writes to send data to my nRF52832 application. For some reason, on the third queued write reply (in nrf_ble_qwr.c) sd_ble_gatts_rw_authorize_reply returns...
I'd like to build a prototype using the nrf9160DK that samples audio from a microphone and plays it back. Given that the dev board has Arduino compatible headers, I'm assuming...
Hello,
we are trying to add log functionality to our application (nRF52 SDK 15.3 SD6.1.1) and we have few questions:
1. can two uart and flash backends coexists in...
I'm trying to do step-through debugging with the nRF9160 DK using Segger Embedded Studio and it's jumping all over the place. I assume this is due to optimization but perhaps...
When bluetooth only is enabled, the program has no problems. After adding USB, the program crashes。 How am I supposed to initialize it, is it a matter of order
<info> app...
Hi,
I'm currently trying to use advertising extensions with my nrf52832. However once I use the
BLE_GAP_ADV_TYPE_EXTENDED_CONNECTABLE_NONSCANNABLE_UNDIRECTED
type...
Our device uses an nRF52840 and we are using SDK v15.3.0 and soft device v140.
In order to optimize power consumption, I want to make a delay function using the RTC (with...
Hi,
We are designing a device based on nRF52840 that implements the Zigbee ZBOSS stack. We are interested to get ZB NVRAM configuration (network id, bindings, reports, etc...
After not having used my Thingy52 for a number of months, I decided to get back to tinkering with it.
When switching it on, it briefly shines a red light and nothing else...
Hello,
I am using the DWM1001 board and would like to receive some bytes over UART to the nRF52832.
I want the device to wait for a certain number of bytes from UART and...
I am using BLE UART and want to incorporate BLE bonding so that IRK keys get exchanged and can resolve the advertisement packet. I am planning to use privacy mode.
Can you...
