Hi
I try to run BLE HRS collector example.
when I run the project, in RTT terminal I have these error
00> sd_ble_enable: app_ram_base should be adjusted to 0x20001CD8...
Google open-sources the firmware needed to build hardware security keys
Google open-sourced today OpenSK, a Rust-based project to aid hardware vendors build hardware security...
I would like to store a simple integer value in the flash write and read after some event. I'm using the mesh example Dimming examples (experimental) in the nRF5 SDK for Mesh...
Hello,
Has there been any success with getting the python bindings for the pc-ble-driver running on openwrt? I've succeeded with the driver itself but not the bindings....
Hi Nordic Team,
In my BLE project I'm creating a Test application which gets all the advertising data from peripheral devices. The complete list of scanned device is received...
Hello all,
According to the documentation and this feedback on a case there is a maximum size for a particular cert before nrf_inbuilt_key_write returns NRF_ENOBUFS . Can...
Hello,
I am using nrf52840 DK, Segger Studio IDE, Win10.
My application is I want to transfer the image from iOS to the DK board.
I am aware of the Image Transfer...
I know there have been many posts on this forum regarding a similar issue, I have spent a whole day reading them and trying to get this working, to no avail.
Basically my...
After nRF52840DK is flashed with open bootloader project through J-link ( usb port J2 on the short side of the board), nRF connect is showing the following interface when...
After reviewing this thread https://devzone.nordicsemi.com/f/nordic-q-a/53743/zigbee-sdk-on-top-of-freertos I managed to get FreeRTOS working with ZigBee and BLE using the...
On the development boards, the JLink OB stops working after 24 days and needs to be disconnected to work again.
This affects at least the USB UART endpoint, but possible...
I have seen some situations where putting the modem into offline mode (CFUN=4) will cause my application to lock up because the at_cmd never returns. It looks like this is...
Hi, I am using Mesh SDK 4.0.0 and have couple of nRF52840 dev kits.
1) In light switch server example of Mesh SDK, is it possible to add more on_off data types to the server...
Hello I am trying to develop an application for advertising in SLOW mode.
Here is my Advertising Init function.
/**@brief Function for initializing the Advertising...
Can somebody help me out the reason behind below failure on thingy 91. I am building asset tracker example using west on command line. Following is the logs that i got after...
Hi,
I am working on the Thingy91 and trying to set up an event when the USB power state changes (USB cable w/power is plugged or unplugged). For now I will just blink...
Hi,
I changed the softdevice on the nRF52833 light client example from the S113 to the S140, but the program
hangs at startup before even enter the main loop (catched...
Hi ,
During the review, I came across the certification question. After some reading, I found some details.
This got me worried because it looks like it is a difficult...
I have found the example using nRF52833 in the latest SDK (ble_app_att_mtu_through....)
I am using Keil uVision 5.29.0 and I have downloaded the software packs 8.27.1, 8...
Hii,
Our input voltage to nrf52840 is 2 volt, we want to know whether 2 volt will be detected has low(0) or high(1) or undetermined state.we are using gpio pins (1,10) and...
Hello,
I'm considering writing BLE relay application, where central side should bond and encrypt connections (cause sensor device requires it and will not function without...
I'm trying to get the most performance per mA out of my nRF52, for test purposes I've used the nrfx libraries to communicate to the peripherals but I want to make my own....
