Hello
I'm using an external flash to store large files, but I’d also like to use the SMP service to exchange small files over BLE. For that reason, I want to create a LittleFS...
When my peripheral calls sd_ble_gap_phy_update, setting rx_phys and tx_phys to BLE_GAP_PHY_AUTO, I receive the BLE_GAP_EVT_PHY_UPDATE event with a status of BLE_HCI_UNSUPPORTED_REMOTE_FEATURE...
Hi all,
I recently bought an nrf52840DK, and yesterday I tried to program an external board through the p20 connector on the DK with the SWD pins. I was able to flash the...
Certainly! Here’s a clear, natural English version of your email:
Dear Specialist,
I would like to better understand the two variables used in the SDK for calculating...
Hi, Using NCS 3.0.0 it would appear that the function sntp_simple_helper does not work with SYS_FOREVER_MS as a timeout value.
Problem: When we pass this value as a timeout...
Hi All,
I have a question and slight confusion as referring to couple of links.
Performing KMU provisioning : Here we are highlighting provisioning of private key up...
In case the DSM metadata is changed compared to what is stored on flash, the 4.0.0 code is supposed to clear the flash from any configuration but this doesn't work properly...
Hello,
I'm pretty new to rtos and totally new to nordic's nRF9160. I've been trying to get this working all day and can't really seem to figure it out based on the resources...
Hello,
We are using nRF52840 with SDK 15.2.0, a bootloader, the bootloader settings and the SoftDevice. Our product has a cellular modem to be able to perform OTA firmware...
Let say a situation where I want to know if the just connected client is the same as the one that was last disconnected, but if the client uses RPA than have somehow to try...
Hello,
I'm developing a BLE device based on nRF52832 and SoftDevice 112 using SDK 15.3.0. The device operates only in peripheral mode with only a single connection to the...
Hi
I try to run BLE HRS collector example.
when I run the project, in RTT terminal I have these error
00> sd_ble_enable: app_ram_base should be adjusted to 0x20001CD8...
Hi,
We are evaluating devkit nRF52840-DK using SDK nRF5_SDK_16.0.0_98a08e2.
The application development is ongoing, based on examples\ble_central , using which we are...
Hi,
I have a multilink NUS central that connects to several NUS Peripherals using SDK 16.0, S140 (NRF52840 REV1). Currently I'm testing with only one peripheral, sending...
We're using the nRF52840 in our product.
We require to perform continuous scanning, with little power usage as possible.
We've seen in the Nordic specs and verified with...
Hi,
I'm using NRF52840, and I've developed a feature which bonds with NRF toolbox application. The problem is that when I'm using secured BLE, I can't receive any messages...
Hi,
I have an issue with getting a GPS fix from time to time under the almost same conditions. When it did not get a fix I could see in the UART log that the nRF9160 was...
Our custom board has an nRF52832. In our custom build system the application HEX and SoftDevice HEX are merged together into a single HEX file, this is achieved by Nordic...
We are in the process of getting our product through SRRC certification in China. I am using the radio_test example from SDK 11.0 for this. All is working fine.
However...
I downloaded SDK v16.0 and in the examples, I can't seem to find the dual_bank_ant_s332 folder.
It is present in SDK v14.2.0 in this path
...\nRF5_SDK_14.2.0_17b948a\examples...
