Hello,
I've seen multiple posts related to this question, but they're not very recent so I wanted to check if there's an updated answer.
Are non-simultaneous multi-image...
I have an Ubuntu Machine where I successfully installed Zephyr SDK and toolchain following instructions given in the official getting started guide here . I was able to compile...
Hello,
I have a custom PCB with the nRF5340 chip. I’m able to flash the board using a J-Link. I’d like to rename the device so that it advertises a specific Bluetooth name...
Hello,*
I'm new to nRF Connect SDK environment, but I'm used to work with Zephyr.
I'm actually confused using west.yml file. I created a new application based on existing...
Hey guys,
I use SDK 3.0.2 and toolchain 3.0.2 and want to start with the modem shell example: https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/samples/cellular/modem_shell...
I made a custon pcb and until now it is working as expected . I am using the me54l14 module by minewsemi and i want to enable the CTE capabilities so that i can have angle...
Help Needed: BLE Not Working on nRF52810 (Tried Zephyr & nRF5 SDK)
Hi everyone, I really need help getting BLE working on my custom board with the nRF52810 . I've been trying...
I'm doing a more complex application than what I'm showing here, but I've reduced it to the minimum. I'm initializing the RTC subsystem, creating a timer, and starting that...
Hi all:
I use the softdevice 2.0.0 and compile bootloader example with "dual bank" on the nrf52 DK,
Running a system that can using DFU from app then jump to bootloader...
Hi ,
I search and found some of questions on this forum wich speak about enabling and disabling peripheral.
I'm ok with that but i have a question about there initialisation...
I am testing the Nordic nrf51822 chip.
I have rewritten a bootloader example allowing firmware updates via Bluetooth LE (FOTA). A mobile phone will sent the update package...
Hi,
I'd like to transfer some data from my App (using fstorage) to the bootloader (using pstorage).
Given that that the two storage mechanisms are different, how can...
Hello, I've been working on porting a bit-banged control of a peripheral to use nRF51 SPI--which is just SPI rather than SPIM (therefore no DMA). Observe the SPICLK waveform...
Hi guys,
I am developing a project where I have a large group of NRF52 chips together in one room. In their normal state each chip is paired as a BLE peripheral device...
We are working on a NRF52 DK. In the data sheet of NRF52832, there is no mention of enhanced shock burst mode or dynamic payload or multiceiver. Do I need to refer additional...
we're using Mbed for NRF51822. our board using 2 GPIOs interrupt.
problem: the Rise edge did not generate the Interrupt event: set EVENTS_PORT.
I try uisng while, but...
Hello,
I will explain my setup:
I have 2 nRF51-DK each one of them connected via I2C and SPI to two different custom boards. One being the central(nrfA) and the other...
Setup: DK #1 is running native S110/SDK10/nRF51, one service 128-bit w/ 16-bit char:
Service UUID: 0x0xb1ad
Service UUID type: 0x0x2
Service handle: 0x0x0c
Service handle...
I found a discrepancy between a tutorial and an application note.
Step 2.A of "BLE Characteristics, a beginner's tutorial" devzone.nordicsemi.com/.../ calls sd_ble_uuid_vs_add...
Hi,
I tried to familiarise with eclipse environment and i have some problems :
The debug and run button. I searched on google but i didnt found anwser.
How can i define...
I find example : nRF51_SDK_7.0.0_2ab6a52\examples\properitary_rf\esb\esb_ptx_prx .
question 1: can i add this example into my project that build on SDK v610 and it run...
