nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
So we are creating a peripheral with a characteristic meant to keep the central synced with the state of our peripheral. The peripheral is running all the time, could be ON...
1. This is on the stock LPN example, with one change to debug-print `status_code` inside handle_appkey_add().
Here is the diff:
2. To reproduce:
- flash and provision...
Hello,
I am currently working on a product with nRF51822 chip, based on SDK10.0.0. The problem is, after a firmware update, my device fails to reconnect to an Android mobile...
Hi,
I've launched wireshark + nRF52 Dongle successfully and I'm also able to select my device (named EWAT AI-No) from the list to sniff. However there's something I don...
I'm working on a simple project based on the USB CDC ACM and libuarte example, the chip is nrf52840.
A function is redirect the USB VCP data to another MCU via UART, just...
Can a server and a client of dimming example, have same element instead of different element ID.
I got worked for server and client model in single node, but they are in...
I am upgrading to SDK 15.3.0 and SoftDevice v6.1.1 from SoftDevice v2.0.0 (S332 stack). Most of functionality has been ported (BLE and ANT) and validated. This particular...
Hi, I'm trying using a setup with transmitter based on nRF24L01P and receiver with nRF24LU1P using Enhached Shock Burst. The problem is the transmission lock (three failed...
Hi,
I am planning system with a BLE peripheral (using nRF52840) and BLE Central (using nRF52840) that is AC powered.
The peripheral will be advertising every ~300msec...
Greetings,
We have some custom boards/devices with nrf9160. They each hold certificates to communicate with aws-iot. The certificates were flashed using the at_client...
Dear nordic,
I am developing a robot controller(Central, nRF51822).
However, I am having a problem with UUID.
And I am using the ble_central (s130 ble_app_uart...
Hi,
I am using nrfutil to generate a bootloader ota package for NRF52832 soic. The command I am using is
I measure on my ubuntu pc, when this command is...
When I was running the heart rate example, I would report this error below, someone tell me what caused this error, which causes the driver to fail to recognize now. But I...
Hello,
The project I'm working in will be using the nrf52840-devkit to create an application which utilizes the on board radio for communication. We will be using nrf connect...
Hi
Hopefully a quick question. I want to send a set of bytes 'shtpData' between to routines but only one byte is being sent:
Sending 'unit8_t *dataPacket' of 5 bytes....
