nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
Hi
I want to receive and send a lot of data in a short time (connection Intervall is set to 20ms). And I get the App-Error 0x3004.
I found this definition for the error...
Hello,
I am currently trying to figure out a problem with my mesh. If I stop the event handling of one node, other nodes in the network will fail to send data from this...
PAN #9 in the nRF51822-PAN-v2.4 document provides a workaround for non-functional OUTINIT. This question and this one improve the workaround and state it's unnecessary in...
We have used the first version of the S132 softdevice with the Engineering A version of the nrf52 chip. Now with the newer Engineering B version, we have moved to the second...
Hello Everyone,
i am trying to simulate the circuit using Proteus so can anyone tell me where can i find the Pspice model files for the Nrf51EVB is it available? any suggestions...
Hello to everyone.
I write code for NRF24LE1 using KEIL and rtx tiny. But i have some problems.
When i power on my device, programm don't run correctly, but when hard...
Hi experts,
The softdevice is s120. I get error code BLE_ERROR_NO_TX_BUFFERS after calling sd_ble_gattc_write() several times. I want to ask what does the tx buffer mean...
I have a strange problem on my target nRF51822. When I try and use the UART interface between my nRF51 and my host MCU, it causes the nRF51 to reset and the RTT terminal to...
Hi,
I've been playing with NFC on nRF52. It sends "Security Manager TK Value" over NFC. There is currently no option to use LE SC over NFC in examples, which is to send...
Hello
I have an problem using I2C on my custom board which uses an Nrf51422 SOC.
I have an RTC chip connected to it and I have no idea how to use your libraries.
The...
Hi! I'm using Arduino BLE micro and good results so far. With some accellerometers connected via I2C.
Today I have a strage behaviour.
I connect the arduino, ok, open...
Hello everyone,
I have a nRF51822 dev board connected through USB to my PC.
I have connected it to COM5 using Terminal and now I would like to interrogate BLE like we...
Hi guys
I have a custom board with NRF51422QFAA, load "s310_nrf51422_2.0.1_softdevice", program on "nRF51_SDK_7.2.0"
the bootloader I used is "dual_bank_ble_s310"
...
Is there a way to control the max # of packets be transmitted in one connection interval?
(We want to vary it from 1 - 6, knowing that nordic can support up to 6-7.)
