Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
I'm trying to combine these 2 examples. I tried adding the uart code:
uint8_t cr;
while (app_uart_get(&cr) != NRF_SUCCESS);
to apps_ble_uart while loop and the whole...
Hi all,
I´m trying to create my first BLE application with segger embedded Studio.
My Hardware is the nRF52833 DK with a sensor connected to dev Board via I2C lines...
Hi, there in inconsistent data about the number of UARTs in the nRF5340 OPS v0.5.1:
- Page ii (nRF5340 features) states "Up to 2x UART (CTS/RTS) with EasyDMA" for the application...
Hello.
I'am new to developing with The Thingy 52 and just trying out simple things. I wanted to see if i could toggle/set one of the pins high from the code but havent had...
Dears,
I'm trying to run the mbedtls library with thread safety with the freertos, already defined MBEDTLS_THREADING_C and MBEDTLS_THREADING_ALT in the user_mbedtls_config...
I have never used the GPIOs near the RF pin (GPIO 22, 23, 24), until my latest project, which I needed to due to pin limitations. It is normal for pins adjacent to RF outputs...
Hi.
I try to test using ble pc-drivce C library & 52840 dongle on pc.
except custom service. everything is fine.
under below is custom service pic.
...
This seems to be a recurring question. I suspect the Wireshark/nrf-Sniffer setup is delicate enough that minor changes/upgrades in any of the components causes a problem....
nrf52832 , SDK_V15.3 , ble_app_uart sample code , data communication problem.
Hello there...
I use the SDK V15.2, ble_app_uart sample code, on the nrf52832
seems the...
Hello,
Currently working with Segger 4.42 and SDK 15.0
I've searched around the devzone on doing a passkey connection between my server and central.
I've used the ble_app_gls...
Hi, I'm having trouble pairing with Android devices using the SDK's ble_app_gls example, when I try to pairing with any andoid device it throws the following error "couldn...
I Modify my code for 7 buttons from 7 gpios. But my code has a issue at sdk_config.h. The define of GPIOTE_CONFIG_NUM_OF_LOW_POWER_EVENTS is 9. When I built the code and download...
Hi all,
The nRF52832 spec. document specifies that the current consumed in System OFF / No RAM retention / Wake on LPCOMP mode is 1.9uA. However, if I measure the current...
