Hello everyone,
I'm reaching out to this forum in a bit of a bind and hoping someone might be able to offer some guidance or assistance.
I'm trying to download the S340...
Hello LE-Audio team,
By any chance, do you have a working code base that supports a headset with 2 end points instead of just one as your sample nRF5340_Audio kit?
If...
Hi, I just tried to connect LSM6DSV IMU with nRF52840dk
The whole folder structure is shown below :
1. I set nrf52840dk_nrf52840.overlay file first.
2. I...
Hello,
We are designing a new Zigbee/Thread end-device sensor and I'm wondering what is the recommended part for it.
I have a demo running with nRF5340 (because the platform...
Hi Nordic team,
I'm using the nPM2100 PMIC in my design to power a microcontroller. The microcontroller sets the nPM2100 into Hibernate mode , and a vibration sensor connected...
Hello,
We are currently using the nrf52840 for development using Zephyr v3.7.99-ncs1 .
We want to use the UART in low power mode and therefore, we have used the zephyr...
My attempts to configure the Zephyr device tree to run littlefs on an external SD card have repeatedly resulted in what appears to be the creation of a small littlefs instance...
I try to bring an old Project (2017) back to life and use the new SDK 16
the Code usese BLE_GAP_TIMEOUT_SRC_ADVERTISING, but that is removed in the new SDK version,
what...
51822
SDK11
Can we change the advertise interval after 51822 started? I need to change the interval to lower / higher based on the user phone. For example, if its IOS...
How does Broadcast characteristic property of GATT can allow BLE observers devices to read the data without being connected with the device? Does this mean we share data without...
We recently ported to the nRF52832 and our electrical engineer had to make a couple changes from the reference design due to space constraints. The port has worked well during...
Hi! I'm trying to measure the voltage drop across a custom PCB we're developing. This was done while trying to get a clear sense of the current consumption used by our board...
Hi , I am using nrf52832 and try to implement a high throughput in ble5.1. i interface memory with nrf52832 my task is to read the memory and send the data to the app with...
Hey Nordic Team,
I noticed an issue with the SDK and `nrf_serial.c`
After deactivating all legacy code and removing all references to standard UART I noticed that I was...
I need a UARTE driver that does a few things differently to the provided UARTE driver and hence I am writing my own based on nrfx_uarte.c . At the moment I am testing the...
I would like recieve all advertisement in my way, and I development my application on the DK PCA10056. My code as below:
But, I can't recieve any valid advertisement!...
Hi
nRF52833, SDK16
When using a UARTE interrupt I get a fault which I cannot locate, I have the following code:
When my 4 bytes are recieved, i get a fault and the...
Hello,
I'm chasing a bug and narrowed it down to a minimal failing case. Even it's only very few lines, I'm still failing to grasp what's actually happening.
Taking the...
Hey guys,
I'm working with SES, nRF52832 and SDK14.2.0.
I have a timing problem and would like to describe the problem from the beginning.
I have a 1-wire temperature...
Hi.
I'm having Segfault issues with our company's custom boards based on nRF52840 chips.
I do several re-flashing with J-Link EDU Mini Programmer on a daily basis with...
Hello, I am reporting here an issue that I detected by using NRF connect on iOS (cf https://github.com/NordicSemiconductor/IOS-nRF-Connect/issues/56 ) The issue is that the...
