I am working with NRF52840 with SoftDevice S140 and SDK v17.1.0.
The boot loader address for this chip is 0xF8000. I can set up one of the 'fstorage' module with the address...
Hey everyone,
Does anyone here have experience with firmware OTA updates over the JIO NB-IoT network? The process seems a bit different since JIO Cloud always sits between...
Hello:
The latest nRF54L15 Errata for Rev 2 shows that the previously reported "GPIOs can exhibit radiated emissions" is no longer present in the Rev 2 SoC.
Can you please...
Hi, this is a very broad issue that i am having, because i dont know the source of it. I am simply unable to use the bme68x IAQ library. i have downloaded the external bsec...
Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi,
I encounter a issue with my printed broad that mainly copy the thingy52. I download the thingyv210HW10.hex into my hardware. And then I debug the code (thingysdkv210...
Hello,
Currently, we are working on a product which leverages the following:
NRF52832 (64KB RAM and 512 KB Flash)
SDK v11.0.0
Soft Device 132
It has been reported...
Hi,
I see from the code in GitHub:
https://github.com/NordicPlayground/fw-nrfconnect-nrf/blob/master/samples/nrf9160/gps/src/supl_support.c
That the new A-GPS is using...
Hi! I'm performing buttonless Secure OTA DFU operation on some custom boards of mine. I'm using nRF Connect v3.3.1, and at the moment I'm flashing a zip file containing my...
We have a door lock product. At first, the capacitance value of bluetooth frequency deviation was not adjusted, and then it was very difficult for apple to connect with vivo...
Hi,
I have a problem that can not receive FDS_EVT_WRITE event, but fds_record_write return NRF_SUCCESS when using FDS and FreeRTOS simultaneously on nRF52840. And FDS_EVT_INIT...
Hi,
In the ble_app_uart example I am trying to read a binary file and send it to the application using nRF52840 board. I have send 32 packets of data periodically.If a delay...
Hi. I am looking for a reference FW design for BTLE where I can define a custom Service and Characteristic where I can send arbitrary (minimal length) data from peripheral...
Hi,
In our application, LCD will occupy 150KB RAM, and algorithm will occupy 60KB, but 52840 only has 256KB ram, so 256KB RAM is not enough for our application;
We want...
To realize multi touch in hid, we need to realize get report request to get the maximum number of support points and set report request to set touch mode. In the SDK 15.3...
Hello,
I'm trying to add a third characteristic to my BLE service and when I add it, my device "fatally" crashes in Release mode with no meaningful error information ...
Hi I'm having trouble updating the firmware on a custom board using JTAG through the NRF9160 DK.
I've attached the log file from the programmer of the error I'm getting...
I loaded up the zephyr sample blinky example, compiled ok, and went to download to the nrf5340-pdk...
I got the following error dialog plus some more misc. errors (see output...
Hi
nrf52833 SDK16
The following code works fine on UART 0 but not on UART 1
The problem seems to come from nrfx_uart.c
There is no support for a UART1, so...
Hi,
I've built a project out of the USBD_ACM_CDC example in which I have added a SPI master driver. This project has a timer interrupt that will shoot off every ~500us and...
