Hi everyone, I have a custom board in nrf52833. Currently, the gpios on nrf52833 are gone, except for the NReset pin (P0.18). Can I configure the NReset GPIO as a GPIO I/O...
My eval setup is PPK2(source mode) -> nPM1300EV - -> nRF54L15DK. I have my load connected to BUCK2, everything else is disabled.
I'm getting higher than expected input current...
I am currently attempting to send HTTP requests (GET and POST) with my nRF9160 DK over an LTE connection. I have tried running the HTTP client sample code under zephyr/samples...
Hi,
Currently, we develop a prototype that needs to communicate with WuR; the FH101RF. Could you please tell me if it is possible to communicate with it? If not, can you...
I am testing gnss without lte connectivity, which seems to work ok.
Except when I get "The modem has detected a reset loop. LTE network attach is now restricted for the...
Hello, could you please provide me an working example of TCP socket communication using Thingy:91X by LTE-M/NB-IoT?
I haven't found any (only UDP and I need TCP).
Thank...
Hi,
I am using the nrf54l15 on a custom board in our current project and want to use it with DFU over BLE FOTA as well as TF-M.
I can compile the project just fine before...
Hi,
I am trying to update the battery level of my Battery Service but get keep getting an error. The error code is : 0x00003002. I cannot find any mention of what this...
I am trying to start programming in nrf51822 module with the waveshare kit. but the kit always shows the error as switch to boot-loader mode . how to solve this problem?
i am using nrf51822 wavshare kit with ulink2 debugger.
when ever i try to program the kit using keil the error pops like "overlapping of address in 00014000H".
then...
Hi,
I am using nrf51822 and SDK 8.0.0 , SD2.1.0 as an central and SD8.0.0 as peripheral. I am following ble_app_multilink_central and ble_app_multilink_peripheral example...
Hello,
We have a custom board using nrf51822.
In keil the board is detecting at 20khz clock for SW port in the debug window, we are able to program through keil.
...
This fork of the MBED CMSIS-DAP firmware seems to be the latest updated one. The title says, 'Interface firmware providing USB CMSIS-DAP for debugging, USB MSD for programming...
Hello,
I try to change a value by using sd_ble_gatts_value_set(...). If there is a connection, this works fine. But now I have to change the value also, if there is no...
Hi again.
I'm using nRF52 DK board in Ubuntu. I can flash the device with the blinky example (I haven't yet tried the softdevice tough), but I cannot really get any traces...
20160316_113235.jpg Hi guys,
i have 20 nodes and a central in my network, that are very close to each other except central device ( All of nodes are in a approximately...
Hi,
I'm wondering why are there scan parameters on creating connection? If I refer to SD130, create connection function , there is a note which tells us that if scan is...
I have 2 existing products, one using the nRF24LE1 and the other having a 2.4GHz ANT radio. Is there a way to have the 2 products communicate wirelessly? If it is possible...
Hi.
Quest to get the toolchain working under ubuntu continues.
I've done the eclipse and jlink config as explained in the nrf51 linux tutorial (with of course keeping...
In an RFID application, we have nrf24l01+ and SMT32F4xx on the Reader and nrf24lu1+ on the tag.
The Reader is acting as multiceiver currently.
Pipe 0 and Pipe 1 are...
Hi Team,
Is it possible to develop MCP like other application which runs on Linux (say Ubuntu) using BLE dongle?
Where to start for this!? Any guideline or documentation...
Can smone help me:
An error pops-up…
“
RESTRICTED VERSION WITH 0800H BYTE CODE SIZE LIMIT; USED: 0DC4H BYTE (172%) *
“
This could be due to EVAL version of uVision...