Hi,
I want to configure P1.02 and P2.06 as normal GPIO for my nrf54l15 custom board. For this I have added the following in my .overlay file
From https://devzone.nordicsemi...
Hi Nordic team,
I’ve been working with the nrf_dm sample from NCS 2.9 to perform distance measurements using multiple nRF52840 devices. The sample works well, and I've made...
Hello
I'm working on a custom electronics board with an nrf54L15 (QFAA). This MCU is interfaced with an EEPROM memory (24FC16T) via an I2C bus connected on P1.03(SCL) and...
Hello everyone,
I am currently working on implementing the flash protection feature for the 54L05 chip. My objective is to safeguard the code storage area from unintended...
Hello Team,
i am trying to read multiple mcp9600 on the nrf9151 on my thingy 91x. I connected 3 of the mcp9600 to my stemma QT connector and it all works fine.
However...
Hi all,
I could not find similar questions raised on the forum and I hope someone can help me.
I have an application to connect to a mqtt server, developped on the latest...
We are currently working on a project using the Nordic nRF5340 and nRF7002 DK, which includes 1MB of internal flash and 2MB of external SPI flash. Our application codebase...
Hi there,
I'm working with a custom board based on the Raytac AN54L15Q module and encountering higher-than-expected power consumption when trying to profile using the system_off...
Hi,
1.In ncs v3.0.0, can both USB DFU and UART DFU be enabled simultaneously on the nRF5340 DK board? 2. If USB and UART DFU can be enabled simultaneously, then how should...
Development board: nRF54L15DK i I'm already using "Find My Example" to connect to the "Find My" app on my iPhone. At the same time, I also want to connect to nRF Connect....
Hi,
there is my project rom size in memory report , I would like to asking what is the "NO Paths" item and hidden item
they hold my 20% ROM size. and what is the content...
Does the nrf54l15 have a register to specify the boot area? Similar to the NRF_UICR->NRFFW of nrf52833.Or does the nrf54l15 have to boot from address 0x00000000?
Hi,
We're at a point in our project where we're working through some regulatory testing for ETSI/FCC certifications with our BLE dongle board (nRF52840 + nRF21540 FEM...
Hello Nordic,
We have recently purchased an nRF52840 Dongle. We were able to sniff the BLE packets over the air. So it is found that all the packets that we are able to...
I was implementing custom services and characteristics(softdevice:s140, ble) on the nrf52840 dongle, however I couldn't get it to work, even though my code seemed correct...
Dear All,
I updated Toolchain and SDKs to last version v3.0.2 and I'm going to add build configuration as suggested here How to create and build an application .
My board...
Hello,
I am trying to modify peripheral_hids_keyboard 's security configuration as Security Mode 1 Level 2.
According to some Q&A thread, I tried the following:
1...
The nrf_cloud_multi_service sampe is running in to fatal error while trying to downolad A-GNSS data. The sample is configured to work with NB-IoT and CoAP.
Here is the log...
hi support team,
may i ask how to set static ip address for 7002?
1. i set these configs:
CONFIG_NET_CONFIG_SETTINGS =y
CONFIG_NET_CONFIG_NEED_IPV4 =y
CONFIG_NET_DHCPV4...
Hey everyone,
I have designed a custom board with a bunch of nordic IC's (nRF54L15, nRF9151, nRF7002 & nPM1300)
I have tested the basic functionality so far, including...
Hi，
Platform : nrf52840, NCS 2.7.0
I would like to get the MCUBoot image swapping progress without modify the NCS, and display a progress bar on the LCD to indicate the...
