Background
Our device uses the CONFIG_LTE_NETWORK_TIMEOUT option from LTE Link Control, which by default is set to 600 seconds (10 minutes). I haven’t found any specific...
Hello, as the title suggests, I have an issue when powering the nRF9151 DK with an external power supply. Normally, I power through USB, and it's fine. However, when I followed...
Hi all,
I am using and nrf9160, in particular a thingy91. It is running 1.3.7 firmware. I have the SLM sample loaded and can sent AT commands to the device using the nRF...
Hello,
We are working on Zephyr sample app Mesh on nRF52840dongle with nRF Mesh application.
After going through the documentation and few other Q&A on the portal, I was...
Hlo
I have designed a custom board based on nRF5340. Now I am trying to do flashing and RF testing of it through nRF5340 development board but can't even flash it because...
Hi,
I purchased a Qorvo QM33120WDK1 UWB development kit that uses a Nordic nrf52840-DK. I have been using this DK for weeks without issues, but the last time I used it...
We are developing a product that will have a wireless and wired option, based on the NRF52840
The strategy is to release the wired option first, followed by the wireless...
Hi,
Recently I came across this example which gives mesh & uart in single application. now i'm trying to add GATT proxy to it so that i can do provisioning via nrf mesh...
Hi,
I have read the dfu protocal and found that there are three types of dfu transfer which are identified by a firmware ID. Now I want to add a new part to update the user...
Dear,
I am using THINGY91 for proving my concept, I put THINGY91 in the freezer - to adapt to the temperature.
I am using NB_iot of telia (norway)
My problem is: sometimes...
Hi,
I am using the NRF52832 with softdevice 6.1.1
I am using the minimal ble_app_uart ecample, just changes the RX_PIN_NUMBER to 11 an TX_PIN_NUMBER to 12 to mach my board...
Hello ,
I want to read the values from tera term , and PCA10040 have to read that value on polling basis .
Then advertise that values / data as manufacturing data. i am...
Hi
it looks like my MQTT-SN is not working.
I am trying to run MQTTSN Example in nRF52840 devices. https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter...
Hi,
I have 3 Devices that constantly broadcast their position to each other so the other can adjust the position each other. they act like master and slave but ther are...
I'm trying to get the most performance per mA out of my nRF52, for test purposes I've used the nrfx libraries to communicate to the peripherals but I want to make my own....
Dear Nordic
my SOFT DFU fail when I init the WDT, but I have feeddog and disable the WDT, like below:
static bool app_shutdown_handler(nrf_pwr_mgmt_evt_t event) { switch...
When access_model_subscription_list_dealloc() is called the entry is memset to 0 and the ACCESS_INTERNAL_STATE_INVALIDATED flag is set.
The function access_model_subscription_list_alloc...
Hi all,
I have a nRF52 DK (PCA10040 V1.2.1), and I want to learn how to develop on macOS.
I read from this link , and I got following information.
But I cannot know...
Hi,
I use The Texas Instrument software "SmartRF Packet Sniffer Bluetooth Low Energy" to catch the communication between my peripheral build with nRF52832 and Zwift (software...
Hello
I am trying to configure your TWIS (not using the SDK) and have run into the problem that the TWI master cannot pull the SDA and SCL line low. So, the communication...
52832's PDM function. After initialization, call the nrf_pdm_enable function, and then call the nrfx_pdm_start function. NRFX_PDM_ENABLED is set to 1. But the clock pin always...
