I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
hello:
our hardware engineer had designed PCB,it can't reach more than 100m..howerer the nrf52840 DK can reach 300 or more meter.
so is there any people can support some...
When using nrfutil to generate a DFU settings page (with backup page) of settings version 2, the .hex-file generated by nrfutil is not word-aligned, i.e. the number of bytes...
I noticed that as of SDK v16 a required component to use the Soft Device is nrf_section_iter which is located in the directory "\libraries\experimental_section_vars". Is this...
Hello,
The product specification for the nRF52832 only shows 3.0V performance. What is the performance in parameters such as Tx power, Rx sensitivity, maximum MCU clocking...
Hi,
I'm currently developing firmware in the Arduino environment using a dev board (Adafruit Feather nRF52840). Once I complete development, how do I transition the firmware...
Hi, I am developing the application in nRF52832 with SDK_16 in SES.
I have a problem with DFU
I need to run the application and DFU has to be activate only if the mobile...
Hello everyone
I'm using NRF MESH4.0, I have add simple_on_off model to experimental_dimming example,and it works .
My question is : MESH PROFILE V1.0 have mentioned bound...
Hello, i am trying to adapt DFU in the Light switch Proxy server example, however in midle the process of receive the DFU packets i got this error: Abort event. packet loss...
Has anyone (tried to) simultaneously use the same QSPI Flash memory directly from an nRF52840 program and as a USB block device?
We have both functions running in the same...
Hi
I am working with nRF52832 DK, using Segger IDE. I want to read data(a file) from a computer and process the data on DK. Is there any way of doing it? Also, is it possible...
Hi Nordic Team:
Can you help me to support BIS or CIS example .btt file。This file was captured by Ellisys tool。So ,I can refer to file ，and understand 5.2 Core Spec about...
Referencing the recommended 52840 PCB layout for the WLCSP package, we noticed two thru-hole vias in the middle of the ground area (in the center of the package). Do these...
Hello,
I am trying to implement ble DFU on our custom nRF52832 board. Up until now we have had no issues with our application running as SoftDevice+Application but some...
I'm attempting to send a time sync message in a mesh packet. When I construct the packet during it's timeslot (for timing determinism) the system faults during encryption...
