Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
I've got some questions regarding the use of DFU target library. I get my update data from the UART and like to use a setup with two partitions on my device. Is this...
Hello, I am new to android development. I am building an Ble App for some of my work in which I want to include Direct Firmware Upgrade(DFU) over-the-air.
I have building...
Previously, I designed a PCB for the nRF52832 chip using the RFANT3216120A5T antenna ( link ). However, I was only able to achieve a very limited Bluetooth range of around...
Hi Nordic teams :
I find that datasheet v0.8 (page12) shows that SDA do not need clock.
Page 277 still shows that SDA need clock pin.
Could you help to clarify which...
Hi, I previously wrote about an unexpected behaviour which I've made a diagram for below. It's relatively simple though, the COMP watches a voltage and fires a toggle event...
Hi,
1.How to modify the transmission power of the example direct_test_mode to 4dBm? 2. Please provide Method 1 and modify it using the CONFIG configuration? 3. Please provide...
Hi,
the nrf54L15 datasheet states on SPIM "CSN and DCX are not present in all configuration" (p.559). But I can't find the information, when CSN is available.
Dear all,
1) I flash the code through the debugger to my pcb and it is running correctly (just on/off some LEDs).
2) I remove the JTAG+SWD connector, the project still...
Dear Sirs,
I am writing you to inquire about following questions about nRF5340. We are using Laird BL5340 and SDK2.8.0 for our product.
The audio waveform during a wireless...
first i change to my kconfig file add this
source "samples/subsys/usb/common/Kconfig.sample_usbd"
source "Kconfig.zephyr
second I add to cmakelits
include...
Hello Nordic Team,
I am currently working on a Class 3 medical device that requires time-critical communication . I am exploring options for integrating Classic Bluetooth...
A few years back I used a multilink project developed by one of the Nordic support personnel, to allow using the nRF52840 devkit board to talk to one of several Peripherals...
Hey there! I'm just a beginner and was working on a simple UART project in Segger Embedded Studio. The codes were working fine until I started encountering multiple errors...
Dear Nordic,
I am currently conducting a task where one initiator performs Channel Sounding sequentially with three reflectors.
My approach is as follows: First, I...
In my project (SDK 2.9.1), I have configured a USB Mass Storage (MSC) device that uses a QSPI flash, like the one on the 52840DK board.
My system goes into sleep mode...
