Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hi all,
I was testing with a new nRF51 Dongle recently and am finding that it disconnected from any peripheral after 15-18 seconds. Generally a little while after a Connection...
I had a PWM question ( here ). It was recommended that I install SDK 10 and use the PWM files from SDK 10. I installed and copied the PWM files from 10 to 9 and opened my...
Hi, I've compiled program from this link:
developer.mbed.org/.../
The problem is that I can't connect to my DK by nRF UART 2.0 app, probably because not every UUID is...
I am working on adding a timer in the ble_app_uart sample, aiming on disconnect with device which doesn't send any data in specific time, such as 5 seconds.
Now I have...
I get NRF_ERROR_SVC_HANDLER_MISSING error in spi_open function.
uint32_t err = sd_nvic_ClearPendingIRQ(p_spi_instance->irq_type);
APP_ERROR_CHECK(err);
I'm using...
hi,
I need to store persistent data of about 32 bytes in flash, so tried using pstorage APIs (SDK v9.0 on nRF51822 -- 256KB ).
I followed the sample code given here...
Hello,
I am using keil uvision 5.17, sdk 9.0.0 and sd 130.
Once I programmed whole application through mbed,
Then I moved into keil and implemented all function....
We are trying to communicate to NRF51422 through PC using UART communication. But the programs works fine with nRF51822 Dongle and DK. But it does not works with another dongle...
Hi experts,
I need nrf51822 to send thousands of packets (notification) to Master Control Panel (PC), and expect for high data rate. So, I turned the connection interval...
if initial uart_config() before ble_stack_init(), softdevice_handler_init will be failed!
with SDK 6.0
softdevice_handler_init() will returns 0x00001001 ("NRF_ERROR_SDM_INCORRECT_INTERRUPT_CONFIGURATION...
I am trying to generate code using BDS and the Nordic Plugin 1.2 but I keep getting the following error. I have reviewed the XML but I can't seem to find the issue. Any thoughts...
I've been fighting this bug for a few days now and I thought I'd share what I discovered in the process.
I wanted to set up a couple PWM channels to control a few LEDs...
getting problem in implementing uart. code is here
#include <stdio.h>
#include "boards.h"
#include "app_util_platform.h"
#include "app_uart.h"
#include "app_error.h...
I implemented measuring of Lithium battery level with the help of thread How to measure Lithium battery voltage . I am using nRF51422 with SoftDevice 110 and SDK 9.0.0 and...
