Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Dear Nordic,
Can nRF8001 to provide the iBeacon adv. data on air ? (with broadcast pies ?)
If yes, could you please provide an example for iBeacon?
Cheers,
JASO...
I use a S120 central to test a multi link connection.
\Nordic\nrf51822\Board\nrf6310\s120\experimental\ble_app_multilink_central
when the connection is established , the...
Hello,
I have taken a pre-generated XML config for nRFgo and modified it by adding some services
Here is what my config looks like
gyazo.com/bc330e7590afaa22533c200ff17eb902...
I can't figure out why but my build cannot locate files that are included in the makefile.common
I'm using SDK 5.1.0 and the ble_app_hrs project. It seems it can't find one...
My device is smart watch. We transfer some data to phone and receive notification from phone over BLE.
My question is those two functions(connect_params_init and sec_params_init...
Hello
I'm new in the world of nordic semiconductor and I've a little problem. I would like to transfer ANT+ data of a HRM Garmin in serial protocol to my PC. I use a nRF51422...
Hi,
I transmit a data packet to AP2, i wonder if it needs a sequence for resetting or not while AP2
initializing.
And, I send a packet data to AP2 by UART(AP2...
Hi Folks,
I'm experiencing a problem with the nRF8001 setup. After I send the last setup packet, I still receive:
0x03 (length), 0x84(CommandResponseEvent), 0x06(Setup...
I'm getting this error, but oddly it's coming up somewhere in the MIDDLE of my build, and not always the same point.
I have modified the HEAP size to be 0 as I don't do...
Hello !
I have just received the Evaluation Kit nRF51822-EK. I succeed to compile link and load the blinking leds example from my Linux box. I modify the example to use...
So, how do I control where my app is going when gdb pushes it to the device?
I'm using s110 6.0.0, no boot loader. How do I make sure my app is going to where the SD will...
Hello,
I'm trying to make use of the AES crypt code from the application level code.
Per devzone.nordicsemi.com/.../51822-aes-encryption-and-decryption-demo-code
...
I am planning to record some information in the flash of the nRF51822. This will occupy a large circular buffer (quite a few kb), and new data (in chunks of around a dozen...
hi,
i survey the Bluetooth again , i have some issue about the Connectable mode
Connectable mode.
i see the peripheral connectable setting :
PERIPHERAL :
...
