Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
When writing a post in this forum, I found it somewhat nice to have a preview before I do submit.
Even for questions, answers, comments and pm. May it possible to enable...
Hi
Is the generic attribute primary service 0x1801 added by the soft device?
Bluetooth standards say that the service changed characteristic is optional. I am using...
Hi sir
According to nRF51822 RM v2.1 session 12, there are two high frequency clock: the 16/32 MHz crystal oscillator and the 16 MHz RC oscillator. For nRF51822 BTLE application...
I know the question has been asked, but a few months has passed,
but hopefully to get some new update now.
devzone.nordicsemi.com/.../nrf51822-dk-module-as-master
devzone...
Hello,
i try to implement a simple timer interrupt on TIMER1 using one of the CC registers of the NRF51822. Here is my code:
void init_timers(void) {
// Start 32...
Hi,
I have 2 questions regarding this topic:
Which specific J-Link lite mode do we get from nrf51822 Development Kit? Is it the 9 pins model or 19 pins model?
...
Hello,
I want to implement a proximity central. At the moment, I do not get a bonded connection from central to proximity peripheral (For peripheral i use the proximity...
Hello all,
I have realized my own board with a msp430 microcontroller and a nRF24L01+.
I have configured my nRF24L01+ as described in annex C of the datasheet; the objective...
Is it possible to use the J-link to debug a stand-alone PCA10004 ? I am not using the motherboard. Powering the board separately. When I try and run debug in Keil I get error...
I would like to ask a question about the time of :"Time between DISABLE task and DISABLED event when
the radio was in TX" of the "Jitter". In the picture show the "Jitter...
Dear nordic guy, I'm developing
with nrf51822. I have one question regarding main clock control.
I want to turn on and off 16Mhz clock in application side.
application...
Hello,
I have some code running that transfers binary data from an iPhone to a nRF51822 device (used for firmware upgrade).
I have used a variable length characteristic...
When starting with nRFgo Studio "Erase all", "Program SoftDevice" & "Program Bootloader" to have a almost virgin base without an application, I succeed perform an over the...
